F5F Stay Refreshed Hardware Desktop This processor is overheating excessively.

This processor is overheating excessively.

This processor is overheating excessively.

Pages (3): Previous 1 2 3 Next
R
Rebekaa
Member
167
08-26-2019, 09:46 AM
#11
Corsair TM30
R
Rebekaa
08-26-2019, 09:46 AM #11

Corsair TM30

M
Maxhos_
Junior Member
30
08-27-2019, 03:10 AM
#12
https://www.amd.com/en/support/kb/faq/cp...CPU-Cooler Aka just a clamp for pressure. Might be marginally better than the original paste: Source Guru3d, Cryorig R1 Ultimate cooler: https://www.guru3d.com/articles_pages/gu...019,8.html
M
Maxhos_
08-27-2019, 03:10 AM #12

https://www.amd.com/en/support/kb/faq/cp...CPU-Cooler Aka just a clamp for pressure. Might be marginally better than the original paste: Source Guru3d, Cryorig R1 Ultimate cooler: https://www.guru3d.com/articles_pages/gu...019,8.html

M
MJDPlays
Junior Member
18
09-11-2019, 01:02 PM
#13
You should avoid altering the thermal paste. Working inside a mid-tower case can be quite delicate, so it's best to stay cautious. In the BIOS you might look for settings that help with stability or performance, but don't make any changes unless you're sure.
M
MJDPlays
09-11-2019, 01:02 PM #13

You should avoid altering the thermal paste. Working inside a mid-tower case can be quite delicate, so it's best to stay cautious. In the BIOS you might look for settings that help with stability or performance, but don't make any changes unless you're sure.

C
CROSSBOWWEAPON
Member
164
09-11-2019, 02:02 PM
#14
Upgraded to a board featuring a significantly bigger VRM package. The VRMs and CPU exchange heat via traces on the PCB, leading to elevated average temperatures. Certain thermal pastes may actually work better after a thorough burn-in. This process can require a few days to several weeks, depending on usage intensity. Your temperatures remain within acceptable ranges. Generally, there’s little we can do to address increasing transistor density.
C
CROSSBOWWEAPON
09-11-2019, 02:02 PM #14

Upgraded to a board featuring a significantly bigger VRM package. The VRMs and CPU exchange heat via traces on the PCB, leading to elevated average temperatures. Certain thermal pastes may actually work better after a thorough burn-in. This process can require a few days to several weeks, depending on usage intensity. Your temperatures remain within acceptable ranges. Generally, there’s little we can do to address increasing transistor density.

X
xMagicPvP
Member
154
09-14-2019, 12:48 AM
#15
Consider using a lower vcore value. A negative offset works well, too. You might also disable PBO or let it auto to reduce vcore.
X
xMagicPvP
09-14-2019, 12:48 AM #15

Consider using a lower vcore value. A negative offset works well, too. You might also disable PBO or let it auto to reduce vcore.

I
ITzgabrielly
Member
60
09-14-2019, 01:40 AM
#16
In the past I might have used too much thermal paste, could this lead to another problem too? I was just checking if it was applied uniformly on the whole CPU.
I
ITzgabrielly
09-14-2019, 01:40 AM #16

In the past I might have used too much thermal paste, could this lead to another problem too? I was just checking if it was applied uniformly on the whole CPU.

T
TKDragon99
Junior Member
45
09-26-2019, 11:57 AM
#17
It varies by amount. Generally, most components work best when pressed against the CPU die edge. Usually, a bit more improves performance compared to too little. Avoid replacing the cooler entirely—consider upgrading the cooler instead. For budget options, the EVO 212 is a good choice: https://pcpartpicker.com/product/HyTPxr/...2s-20pk-r1
T
TKDragon99
09-26-2019, 11:57 AM #17

It varies by amount. Generally, most components work best when pressed against the CPU die edge. Usually, a bit more improves performance compared to too little. Avoid replacing the cooler entirely—consider upgrading the cooler instead. For budget options, the EVO 212 is a good choice: https://pcpartpicker.com/product/HyTPxr/...2s-20pk-r1

C
Captain_Ahmet
Junior Member
4
09-26-2019, 07:23 PM
#18
I received the 2700x model but had to use an AIO because the built-in fan couldn't handle the heat during intense gaming sessions, reaching temperatures around 85°C.
C
Captain_Ahmet
09-26-2019, 07:23 PM #18

I received the 2700x model but had to use an AIO because the built-in fan couldn't handle the heat during intense gaming sessions, reaching temperatures around 85°C.

A
aleo13
Junior Member
11
09-28-2019, 12:59 PM
#19
It seems you might prefer handling the noisier fan in the near future.
A
aleo13
09-28-2019, 12:59 PM #19

It seems you might prefer handling the noisier fan in the near future.

B
Babu84700
Member
226
10-06-2019, 05:42 AM
#20
Consider reinstalling the cooler using a blob on the CPU. If it's hard to find the exact middle, place the paste on the cooler and let it spread. If the paste isn't too thick, it should cover evenly.
B
Babu84700
10-06-2019, 05:42 AM #20

Consider reinstalling the cooler using a blob on the CPU. If it's hard to find the exact middle, place the paste on the cooler and let it spread. If the paste isn't too thick, it should cover evenly.

Pages (3): Previous 1 2 3 Next