F5F Stay Refreshed Hardware Desktop Obtaining extremely high temperatures using 5800x3D.

Obtaining extremely high temperatures using 5800x3D.

Obtaining extremely high temperatures using 5800x3D.

Pages (3): Previous 1 2 3 Next
S
SugarCandy21
Member
196
12-07-2022, 07:30 AM
#11
Sure, I'll switch the mounting tonight and reapply thermal paste along with re-seating the CPU to check if it makes a difference. Appreciate the help.
S
SugarCandy21
12-07-2022, 07:30 AM #11

Sure, I'll switch the mounting tonight and reapply thermal paste along with re-seating the CPU to check if it makes a difference. Appreciate the help.

E
ErbearIV
Junior Member
25
12-08-2022, 06:54 PM
#12
You can place the radiator at the top if space allows, using fans to draw air from above and letting the rear fan expel it more quickly. This setup enhances airflow at lower fan speeds and works best for AIO mounts when the radiator is positioned at the top. Also, ensure both fans are set identically and that they don’t work in opposite directions through the radiator.
E
ErbearIV
12-08-2022, 06:54 PM #12

You can place the radiator at the top if space allows, using fans to draw air from above and letting the rear fan expel it more quickly. This setup enhances airflow at lower fan speeds and works best for AIO mounts when the radiator is positioned at the top. Also, ensure both fans are set identically and that they don’t work in opposite directions through the radiator.

P
Pixels_
Member
70
12-10-2022, 03:12 PM
#13
Sorry to hear about the issues with your motherboard and radiator fit. It sounds like there were a few hiccups updating your profile. I’ll make the necessary adjustments and try again later this evening. Thank you for letting me know!
P
Pixels_
12-10-2022, 03:12 PM #13

Sorry to hear about the issues with your motherboard and radiator fit. It sounds like there were a few hiccups updating your profile. I’ll make the necessary adjustments and try again later this evening. Thank you for letting me know!

J
Jorski
Member
219
12-10-2022, 11:22 PM
#14
Avoid having the radiator installed at a low position. It should be positioned as high as feasible, ensuring the pump stays below the radiator's top. Many people make the error of placing it as low as possible—always aim for the highest placement.
J
Jorski
12-10-2022, 11:22 PM #14

Avoid having the radiator installed at a low position. It should be positioned as high as feasible, ensuring the pump stays below the radiator's top. Many people make the error of placing it as low as possible—always aim for the highest placement.

S
Sofi41505
Member
149
12-17-2022, 01:10 PM
#15
The radiator reaches its maximum height in this setup, with the tubes extending from the top. I plan to switch the mount tonight so the tubes sit at the bottom of the radiator.
S
Sofi41505
12-17-2022, 01:10 PM #15

The radiator reaches its maximum height in this setup, with the tubes extending from the top. I plan to switch the mount tonight so the tubes sit at the bottom of the radiator.

C
ConanGhost
Member
152
12-19-2022, 07:35 AM
#16
Also verify BIOS settings for CPU_FAN1/2 configuration as Water Pump (WP) and switch control mode from Auto to PWM. If you have multiple CPU headers, connect the pump to the first header, adjust it to Full Speed, then attach the AIO fans to the second header, reconfigure them to PWM, and observe CPU performance on Performance or a custom curve.
C
ConanGhost
12-19-2022, 07:35 AM #16

Also verify BIOS settings for CPU_FAN1/2 configuration as Water Pump (WP) and switch control mode from Auto to PWM. If you have multiple CPU headers, connect the pump to the first header, adjust it to Full Speed, then attach the AIO fans to the second header, reconfigure them to PWM, and observe CPU performance on Performance or a custom curve.

A
Adidas_X
Junior Member
47
12-31-2022, 07:45 AM
#17
You're right to recall those details. The pump used a 1.4-pin connector, and the radiator fans were likely connected in series via a splitter from the pump.
A
Adidas_X
12-31-2022, 07:45 AM #17

You're right to recall those details. The pump used a 1.4-pin connector, and the radiator fans were likely connected in series via a splitter from the pump.

B
Brummer0815
Member
63
12-31-2022, 08:09 AM
#18
A splitter should be connected to the pump, yet the fans must also have their own dedicated header connection.
B
Brummer0815
12-31-2022, 08:09 AM #18

A splitter should be connected to the pump, yet the fans must also have their own dedicated header connection.

S
SlaRac0nte_
Member
217
12-31-2022, 05:04 PM
#19
I’ve repositioned the pump using fresh thermal paste (MX-5). The radiator was rotated so the tubes sit at the bottom. Two problems: I moved a fan from the bottom to the top because it didn’t fit with the tubes, and the tubes are slightly protruding—hoping they’ll bend inside the case. There’s only one 4-pin connector at the pump and for the two fans on the radiator.
S
SlaRac0nte_
12-31-2022, 05:04 PM #19

I’ve repositioned the pump using fresh thermal paste (MX-5). The radiator was rotated so the tubes sit at the bottom. Two problems: I moved a fan from the bottom to the top because it didn’t fit with the tubes, and the tubes are slightly protruding—hoping they’ll bend inside the case. There’s only one 4-pin connector at the pump and for the two fans on the radiator.

H
herokinkkonk
Junior Member
45
12-31-2022, 06:10 PM
#20
Here are your latest idle thermals.
H
herokinkkonk
12-31-2022, 06:10 PM #20

Here are your latest idle thermals.

Pages (3): Previous 1 2 3 Next