F5F Stay Refreshed Hardware Desktop What is this debug beep?

What is this debug beep?

What is this debug beep?

M
MavrosGR
Senior Member
Find
579
09-30-2020, 02:36 PM
#1
I just installed a 3060ti and previously had an Asus TUF B450m plus II Ryzen 5 3600X setup with Gigabyte, GTX 1070, and other components. I was using Windows 10 at 64-bit. After installing the Aurora 3060ti, it began beeping during startup—first a normal boot sound, then four consecutive beeps. Everything works now, but I’m still curious about the issue. Please find the video attached. Let me know if you need more details! Thanks! 20250104_162152.mp4
Reply
Reply
M
MavrosGR
09-30-2020, 02:36 PM #1

I just installed a 3060ti and previously had an Asus TUF B450m plus II Ryzen 5 3600X setup with Gigabyte, GTX 1070, and other components. I was using Windows 10 at 64-bit. After installing the Aurora 3060ti, it began beeping during startup—first a normal boot sound, then four consecutive beeps. Everything works now, but I’m still curious about the issue. Please find the video attached. Let me know if you need more details! Thanks! 20250104_162152.mp4

Reply
Reply
I
iiCatherineii
Member
Find
159
10-02-2020, 03:36 PM
#2
On ASUS's support page you can find details about the sound codes from the speaker. The sequence "one long and four short beeps" indicates a CPU Fan Error or related issue. Make sure your CPU and fan are properly installed. If the problem persists, try loading the default BIOS or clearing CMOS. This sound pattern usually means a successful POST followed by quick beeps, with brief pauses between them.
Reply
Reply
I
iiCatherineii
10-02-2020, 03:36 PM #2

On ASUS's support page you can find details about the sound codes from the speaker. The sequence "one long and four short beeps" indicates a CPU Fan Error or related issue. Make sure your CPU and fan are properly installed. If the problem persists, try loading the default BIOS or clearing CMOS. This sound pattern usually means a successful POST followed by quick beeps, with brief pauses between them.

Reply
Reply
P
pyromaani
Member
Find
61
10-02-2020, 10:19 PM
#3
That makes sense too. I just relinked both the CPU and fan, reset the CMOS, but it kept beeping at me.
Reply
Reply
P
pyromaani
10-02-2020, 10:19 PM #3

That makes sense too. I just relinked both the CPU and fan, reset the CMOS, but it kept beeping at me.

Reply
Reply
S
Sqorck
Junior Member
Find
47
10-04-2020, 03:41 PM
#4
You can still access the BIOS or boot into Windows despite the beeping. I’d look inside the BIOS to verify the CPU cooler’s RPM reading. Did you clear the CMOS by following the proper steps—either through the BIOS or by removing the button cell battery?
Reply
Reply
S
Sqorck
10-04-2020, 03:41 PM #4

You can still access the BIOS or boot into Windows despite the beeping. I’d look inside the BIOS to verify the CPU cooler’s RPM reading. Did you clear the CMOS by following the proper steps—either through the BIOS or by removing the button cell battery?

Reply
Reply
0
05matthew05
Member
Find
62
10-04-2020, 10:05 PM
#5
I can operate the PC normally despite the beeping. I reset the CMOS by disconnecting the power source and then briefly connecting the switch for around five seconds, following the instructions in the manual. I also attempted to remove the button battery and the outcome remained consistent. The BIOS displays fan RPM and allows me to adjust the speed.
Reply
Reply
0
05matthew05
10-04-2020, 10:05 PM #5

I can operate the PC normally despite the beeping. I reset the CMOS by disconnecting the power source and then briefly connecting the switch for around five seconds, following the instructions in the manual. I also attempted to remove the button battery and the outcome remained consistent. The BIOS displays fan RPM and allows me to adjust the speed.

Reply
Reply