The storage process didn't unfold as expected.

Pages (3): Previous 1 2 3 Next

OCQ
Junior Member

11-08-2019, 08:31 PM

#11

Configuration for strength settings.

OCQ

11-08-2019, 08:31 PM #11

Configuration for strength settings.

GhostlyGalaxy
Junior Member

11-09-2019, 04:45 AM

#12

No, you don't set all CAD bus timing configurations to zero.

GhostlyGalaxy

11-09-2019, 04:45 AM #12

No, you don't set all CAD bus timing configurations to zero.

Airbus_A321
Junior Member

11-13-2019, 08:37 AM

#13

Used a Ryzen Dram Calculator to analyze performance metrics.

Airbus_A321

11-13-2019, 08:37 AM #13

Used a Ryzen Dram Calculator to analyze performance metrics.

Darthdread1
Member

11-15-2019, 10:11 PM

#14

I don't recall the original configuration, or are you referring to maintaining settings at 20, 24, or 24?

Darthdread1

11-15-2019, 10:11 PM #14

I don't recall the original configuration, or are you referring to maintaining settings at 20, 24, or 24?

WeedGod
Junior Member

11-30-2019, 08:40 AM

#15

yep, keep them as is for now. for the most part, just as a quick tip, set the values to what dram calculator said. but don't go over 1.45 for dram and 1.2 for soc and see how far you can go.

WeedGod

11-30-2019, 08:40 AM #15

yep, keep them as is for now. for the most part, just as a quick tip, set the values to what dram calculator said. but don't go over 1.45 for dram and 1.2 for soc and see how far you can go.

biomedestroyer
Member

11-30-2019, 10:11 AM

#16

It doesn't want to launch again. It seems I can't open this kit, or the timing settings (20, 24, 24) are incorrect.

biomedestroyer

11-30-2019, 10:11 AM #16

It doesn't want to launch again. It seems I can't open this kit, or the timing settings (20, 24, 24) are incorrect.

SkyLionGame
Member

12-01-2019, 04:46 PM

#17

Reset the CMOS, it's a trial and error approach. Verify the original settings.

SkyLionGame

12-01-2019, 04:46 PM #17

Reset the CMOS, it's a trial and error approach. Verify the original settings.

harm2046
Member

219

12-01-2019, 07:12 PM

#18

Your settings seem too loose, which means much of your effort is lost. Consider using 3000mhz with Cas16 instead. Clarify what’s happening—don’t just jump to higher frequencies without understanding why.

harm2046

12-01-2019, 07:12 PM #18

xXchelliXx
Junior Member

12-01-2019, 08:56 PM

#19

Sure, I'm here to listen. What would you like to talk about?

xXchelliXx

12-01-2019, 08:56 PM #19

Sure, I'm here to listen. What would you like to talk about?

CHadek
Member

12-02-2019, 01:23 AM

#20

The most effective method is gradually raising the frequency while checking stability at each stage. The aim is to maintain timing precision rather than increase speed, using XMP settings for consistency. Alternatively, opting for 3600mhz RAM can be a practical solution. When someone claims they've achieved X frequency, it doesn't guarantee your system will match. Keep this in mind.

CHadek

12-02-2019, 01:23 AM #20

Pages (3): Previous 1 2 3 Next