F5F Stay Refreshed Power Users Networks The Cisco IOS fails to start.

The Cisco IOS fails to start.

The Cisco IOS fails to start.

Pages (2): Previous 1 2
G
GaryDDM
Junior Member
Find
45
07-18-2025, 05:30 AM
#11
Yes, you're correct. It should work that way. Since the AP indicates it can't locate the file or directory, the extraction might have failed. You likely used a different method—perhaps tar -xtract PATH-TO-IMAGE.tar flash to properly extract the archive. Check the folder named "ap3g1-k9w7-mx.153-3.JF15" for any files inside.
Reply
Reply
G
GaryDDM
07-18-2025, 05:30 AM #11

Yes, you're correct. It should work that way. Since the AP indicates it can't locate the file or directory, the extraction might have failed. You likely used a different method—perhaps tar -xtract PATH-TO-IMAGE.tar flash to properly extract the archive. Check the folder named "ap3g1-k9w7-mx.153-3.JF15" for any files inside.

Reply
Reply
L
louracame
Junior Member
Find
40
07-21-2025, 11:44 PM
#12
k9w8 represents the CAPWAP/controller mode, while k9w7 is the lightweight mode. A conversion exists, but it's unclear if any preparation is needed before booting the lightweight image.
Reply
Reply
L
louracame
07-21-2025, 11:44 PM #12

k9w8 represents the CAPWAP/controller mode, while k9w7 is the lightweight mode. A conversion exists, but it's unclear if any preparation is needed before booting the lightweight image.

Reply
Reply
Y
YoloGeek22
Member
Find
152
07-22-2025, 12:05 AM
#13
I used the instructions from the link you shared. I followed their steps exactly, but now I have a different version.
Reply
Reply
Y
YoloGeek22
07-22-2025, 12:05 AM #13

I used the instructions from the link you shared. I followed their steps exactly, but now I have a different version.

Reply
Reply
K
Kunall
Member
Find
205
07-22-2025, 12:20 AM
#14
For autonomous mode, stick with one of the k9w8 images but booting from a k9w7 image is lighter and needs a controller. (Or at least I believe I have the W8 and W7 setups correct) Edit: nvm, I had them swapped.
Reply
Reply
K
Kunall
07-22-2025, 12:20 AM #14

For autonomous mode, stick with one of the k9w8 images but booting from a k9w7 image is lighter and needs a controller. (Or at least I believe I have the W8 and W7 setups correct) Edit: nvm, I had them swapped.

Reply
Reply
N
n_tiffanyblue_
Member
Find
226
07-22-2025, 01:36 AM
#15
I'll check if the files are in the correct subdirectory and see if they exist, then attempt to reload the software again.
Reply
Reply
N
n_tiffanyblue_
07-22-2025, 01:36 AM #15

I'll check if the files are in the correct subdirectory and see if they exist, then attempt to reload the software again.

Reply
Reply
N
Ngiam_x
Junior Member
Find
47
08-09-2025, 09:47 PM
#16
You're experiencing a 404 error when trying to configure in the webgui, even after formatting and re-uploading the file. It seems some versions of the software might have bugs. Have you tried reaching out to the developers or checking community forums for similar issues with the AP3g1-k9w7-tar version?
Reply
Reply
N
Ngiam_x
08-09-2025, 09:47 PM #16

You're experiencing a 404 error when trying to configure in the webgui, even after formatting and re-uploading the file. It seems some versions of the software might have bugs. Have you tried reaching out to the developers or checking community forums for similar issues with the AP3g1-k9w7-tar version?

Reply
Reply
Pages (2): Previous 1 2