The AMD Ryzen 5 1600 performs slightly slower than before.
The AMD Ryzen 5 1600 performs slightly slower than before.
Roland Of Gilead :
MidgetChicken :
Supahos :
It seems you might want to check a couple of things: 1) maybe your overclock isn't stable, try going back to version 3.9 and see how it affects performance. 2) Your CPU shouldn’t exceed throttling limits while gaming. Going to 4.1 just to overheat and slow down would actually hurt performance. For testing, consider using a 2666 and keep it simple to confirm stability. Experiment with different CPU speeds and voltages to find your best results. Also, make sure your BIOS is up to date. If you're running at 3200 MHz, you likely already did that, but if not, update it.
I agree. If you're using a 4.1 version, it’s pushing the chip hard. Even the higher-rated models can’t exceed that. For a 1600 MHz CPU, aim for lower speeds. Reserve 4.1 for high-end cooling solutions—it's probably where you hit your limits.
If your overclock failed on 4.1, it might be too aggressive. The higher binned models (like 1800x) can't go beyond that. For a 1600 MHz CPU, keep it slightly lower. Use better cooling if needed.
Prime95 and Prime95 blendmode cause the screen and keyboard to shut down after about 20 minutes, but your PC continues running. The voltages are set to auto (1.2V for CPU, 1.35V for RAM). Any advice?
First, test Prime95 on a single core only. This helps stress the CPU/cache and shows your maximum temperatures. Run it at stock settings to find your base temp. Then use that as a reference for further overclocking.
For memory testing, try Memtest. Always run it at stock speed so you confirm RAM is working correctly at its rated rate. This gives a solid baseline for future upgrades.
With modern chips like Ryzen and unlocked SKUs, you can independently optimize both CPU and RAM. Start by stabilizing your CPU with a good overclock, then gradually adjust RAM speed to reach the highest stable frequency. Increasing voltage isn’t recommended unless necessary.
Some issues with your performance could stem from your parked cores. In simple terms, a parked core indicates that the processor is disabled, which you generally want to avoid. Here’s how to check if your cores are disabled:
Open windows → Task Manager → Click on the 'Performance' tab at the top → At the bottom, select 'Open Resource Monitor' → Go to the 'CPU' tab at the top → On the right side, look for 14 graphs. The first 12 show your threads/cores. Ensure that at the top of each graph labeled with "CPU 0", "CPU 1" etc., it does NOT say "CPU 0 - Parked".
If any core shows it is parked or grayed out, follow these steps:
Navigate to Control Panel → Click on 'Hardware and Sound' → Then 'Power Options' → Choose 'High Performance'.
If you can't find it, select the 'Hide additional plans' tab and it should appear.
Maybe the issue lies elsewhere. You might want to revisit version 3.9 and check if that improves things. Your CPU should remain below throttling temperatures during gaming; jumping to 4.1 only to experience overheating and reduced performance would not be beneficial. Consider testing with a 2666 and ensure stability before proceeding. Experiment with various CPU speeds and voltages to identify your optimal settings. Also, make sure your BIOS is up to date—probably you’ve already done that unless your RAM isn’t functioning at 3200. If not, updating it could help.
Also, I’ve seen 1500X and 1600X models exceeding 4.1, and there are many 1800X units that push beyond that. It’s possible you’re throttling under those conditions.
Let me know what monitoring tools you’re using for core temps, voltage, and VRM temperatures.
Vellinious :
Roland Of Gilead :
Supahos :
Maybe you should consider these options:
1) Your OC might not be stable, try going back to 3.9 to check if it improves or worsens things.
2) Is your CPU maintaining lower throttle temperatures during games? Going to 4.1 just to overheat and slow down would hurt performance. It’s better to test with a 2666 and keep it stable for reliable testing. Experiment with various CPU speeds and voltages to find your optimal setup.
Also, make sure you update the BIOS if needed. Assuming your RAM is running at 3200, you might already have updated it, but if not, do it now.
If you're using a 4.1 version, that could really stress the chip. Even the higher-tier 1800 models can’t exceed that. For a 1600, aim for slightly lower settings. 4.1 should be reserved for high-end cooling solutions, as it’s likely where throttling occurs.
I’ve seen 1500X and 1600X models exceeding 4.1, and there are many 1800X units that go higher than that.
It’s possible you’re throttling.
Now, about the monitoring tools – what software are you using to track core temps, voltage, VRM temps, etc?
Hi, thanks for the advice.
I use CAM and MSI Command Center for core temperatures.
I mostly check voltage in BIOS; it shows 1600MhZ or the value after overclocking.
If I get 1600, I know it didn’t work, so I revisit the BIOS and adjust accordingly.
MidgetChicken shared some insights with Roland Of Gilead. Supahos suggested checking if your CPU stays below throttling temperatures during gaming; going to 4.1 just to overheat and slow down would not improve performance. It’s better to test with a 2666 and ensure stability before adjusting. Also, updating the BIOS is recommended, especially if your RAM is already running at 3200. Agreeing that a 4.1 OC might be pushing the chip too hard. Ya know... I’ve seen 1500X and 1600X exceeding 4.1, and there are plenty of 1800X models that go higher. It’s possible you’re throttling at that level.
The OP asked about monitoring tools for core temps, voltage, VRM temps, etc.
Hi, thanks for the help. I use CAM and MSI Command center to track core temperatures. I mostly check the BIOS readings—sometimes it shows 1600MhZ or the actual overclocked value. Going with 1600 didn’t work, so I revisited the BIOS settings. Have you tried enabling your cores? I think I missed your earlier comment.
I've already tried many things.
But my CPU and RAM only function at auto voltage settings. Changing those values doesn't improve overclocking much.
Not a huge issue, though.
Right now I'm running at 3.7GhZ with a steady 58°C temperature when using full CPU load.
But I can't get the Corsair Vengeance 2x8GB 3200MhZ to exceed 2667MhZ.
It won't even start if it's at 3200MhZ (maybe a BIOS problem, since MSI has been working on it for weeks – not sure).
Anyone have a solution for this?
Sounds like you've got the bios overclock bug. As soon as you touch the voltage or the multiplier your processor is constantly clocked to 1.2 or 1.6 in windows?
It's a pretty common problem with people on the 350 chipset.
There's some good information on this thread about that bug, and how to work around it.
http://www.overclock.net/t/1628508/offic...wners-club
Vellinious :
Sounds like you've got the bios overclock bug. As soon as you touch the voltage or the multiplier your processor is constantly clocked to 1.2 or 1.6 in windows?
It's a pretty common problem with people on the 350 chipset.
There's some good information on this thread about that bug, and how to work around it.
http://www.overclock.net/t/1628508/offic...wners-club
To 1.6 Yes. I'll check out that forum. Thank you