Only 2133 displayed when XMP is active

Pages (3): Previous 1 2 3 Next

zombistruc22
Junior Member

03-26-2018, 06:00 AM

#11

Also ensure RAM is placed in spots 2 and 4

zombistruc22

03-26-2018, 06:00 AM #11

Also ensure RAM is placed in spots 2 and 4

Tariax
Member

03-26-2018, 12:25 PM

#12

I realized the issue lies with my RAM. I tried the same model in another setup with a B350 board, but it didn’t recognize its speed either. Using a 2666 RAM on the other system worked fine when XMP was enabled, raising it from 2400 to 2666.

Tariax

03-26-2018, 12:25 PM #12

Bopler
Member

131

03-28-2018, 02:22 AM

#13

Have you considered adjusting the RAM speed to its rated setting while using more relaxed timings, or following the XMP profile’s suggested settings? You don’t have to enable XMP to make the RAM function as intended.

Bopler

03-28-2018, 02:22 AM #13

_HardGamer_
Member

181

03-28-2018, 11:57 PM

#14

I tested it on the Gigabyte board too, and also on an ASUS board. I used various speeds starting at 3000, but the only one that worked consistently was 2133.

_HardGamer_

03-28-2018, 11:57 PM #14

I tested it on the Gigabyte board too, and also on an ASUS board. I used various speeds starting at 3000, but the only one that worked consistently was 2133.

CheckMyPvP_
Junior Member

03-29-2018, 08:00 AM

#15

I'm struggling to grasp why the only distinction between them, aside from frequency, is voltage—I really don't know if that difference would be significant.

CheckMyPvP_

03-29-2018, 08:00 AM #15

I'm struggling to grasp why the only distinction between them, aside from frequency, is voltage—I really don't know if that difference would be significant.

Absham
Member

182

03-29-2018, 01:20 PM

#16

The board and memory controller seem to dislike the CL15 at 3000mhz. The board is built to fail the OC three times and enter "safe mode" a fourth time, which is likely causing the issue. Adjust memory timings manually to 16-16-16-16, leaving other settings as auto. Make sure v-mem is set to 1.350v to confirm the voltage. Then find and disable the PowerDown mode (possibly in the timings menu), press F10, and restart. May help.

Absham

03-29-2018, 01:20 PM #16

_ImDustin
Member

230

03-29-2018, 09:15 PM

#17

Unfortunately, nothing went well.

_ImDustin

03-29-2018, 09:15 PM #17

Unfortunately, nothing went well.

MCjeepers1009
Member

212

03-31-2018, 10:14 AM

#18

Command Rate (CR) at one seems to work; consider switching to 2T for better results. wow. You might also try 2933Mhz manually while keeping the current timing settings. Another question: are the memories located in slots A2 and B2?

MCjeepers1009

03-31-2018, 10:14 AM #18

DerpityDerp44
Member

04-02-2018, 08:00 AM

#19

I performed that action, but only the XMP setting was changed and it reached 2666. The Corsair RAM didn’t respond.

DerpityDerp44

04-02-2018, 08:00 AM #19

I performed that action, but only the XMP setting was changed and it reached 2666. The Corsair RAM didn’t respond.

mistermancho
Junior Member

04-03-2018, 08:23 PM

#20

I also changed the CR to 2T during that procedure.

mistermancho

04-03-2018, 08:23 PM #20

I also changed the CR to 2T during that procedure.

Pages (3): Previous 1 2 3 Next