Memory Allocated 16 GB (7.95 GB free) for Hardare: 8 GB

Pages (3): 1 2 3 Next

samaclause
Member

142

09-09-2018, 03:45 PM

Hey everyone, my computer has been having issues for a while now. It’s slowing down a lot, not just because of the low usable storage—only 7.95GB remains—but also since I don’t think the dual-channel setup is being used properly. In the BIOS, the 16GB is listed correctly. I’ve checked msconfig and everything seems fine. I updated and reinstalled the BIOS, reset the CMOS, cleaned the RAM with an eraser, swapped out memory sticks, and even tried a new processor. Since I have a Ryzen 5 2600X with an AMD RX580, 8GB RAM, 16GB storage, and dual-channel support, I’m hoping someone can help me resolve this. Thanks in advance!

samaclause

09-09-2018, 03:45 PM #1

SourMems
Junior Member

09-11-2018, 04:44 AM

Yes, you can perform a similar check. It can assess the entire 16 GB memory space. You might also look in Device Manager if that memory section is linked to a device. Often, reserving such a large amount suggests an unsupported configuration. Your RAM runs at 2133 MHz—consider enabling XMP on both dimming settings, as it may be active only on one.

SourMems

09-11-2018, 04:44 AM #2

Djjeffy
Junior Member

09-15-2018, 07:49 AM

Yes, that's what I'm asking.

Djjeffy

09-15-2018, 07:49 AM #3

Yes, that's what I'm asking.

ajpate
Member

223

09-15-2018, 02:14 PM

Yes, it seems reasonable. The memory isn't locked up as hardware, supporting the unsupported mode idea. Did you ever start your computer using only a single RAM stick? In CPU-Z, you can navigate to the SPD section and see how each module displays its status.

ajpate

09-15-2018, 02:14 PM #4

PedroO_
Senior Member

522

09-22-2018, 03:22 PM

I typically rely on a single stick, which gives me about 8GB available. However, with the second stick I receive around 7.95GB.

PedroO_

09-22-2018, 03:22 PM #5

I typically rely on a single stick, which gives me about 8GB available. However, with the second stick I receive around 7.95GB.

gongstrong28
Junior Member

09-23-2018, 05:29 AM

I noticed that setting 3000 MHz in the XMP file results in 2133 MHz showing up in the task manager.

gongstrong28

09-23-2018, 05:29 AM #6

I noticed that setting 3000 MHz in the XMP file results in 2133 MHz showing up in the task manager.

PinqNoLag
Member

181

09-23-2018, 07:14 AM

It might be another sign of your issue, but I'm not sure what else to attempt. Have you tried running it without XMP?

PinqNoLag

09-23-2018, 07:14 AM #7

It might be another sign of your issue, but I'm not sure what else to attempt. Have you tried running it without XMP?

MJShadow_
Junior Member

09-23-2018, 02:42 PM

Sure, I've already tested it without the xmp. It seems like the issue started after that change. Everything functioned properly before, but now it's not working as expected.

MJShadow_

09-23-2018, 02:42 PM #8

Sure, I've already tested it without the xmp. It seems like the issue started after that change. Everything functioned properly before, but now it's not working as expected.

Dil2601
Member

109

09-23-2018, 10:21 PM

Consider testing with memtest or launching a Linux environment to determine if the issue lies in Windows or a hardware problem.

Dil2601

09-23-2018, 10:21 PM #9

Consider testing with memtest or launching a Linux environment to determine if the issue lies in Windows or a hardware problem.

CatNinjaXD
Member

208

09-23-2018, 11:08 PM

#10

You should obtain error rates, crashes, and data integrity reports to assess the memory stability and reliability of the system.

CatNinjaXD

09-23-2018, 11:08 PM #10

You should obtain error rates, crashes, and data integrity reports to assess the memory stability and reliability of the system.

Pages (3): 1 2 3 Next