F5F Stay Refreshed Hardware Desktop Issues with Trident Z Neo games

Issues with Trident Z Neo games

Issues with Trident Z Neo games

G
GioRollins
Member
53
12-08-2019, 09:24 PM
#1
I recently enhanced my 3900x setup with a 64GB Trident Z Neo package. This configuration matches the claimed 16-16-16-36 specifications at 3600MHz. The system was extremely shaky at the advertised settings but operates smoothly at 14-14-15-36 at 3466MHz. Just a bit of luck with the dimmer?
G
GioRollins
12-08-2019, 09:24 PM #1

I recently enhanced my 3900x setup with a 64GB Trident Z Neo package. This configuration matches the claimed 16-16-16-36 specifications at 3600MHz. The system was extremely shaky at the advertised settings but operates smoothly at 14-14-15-36 at 3466MHz. Just a bit of luck with the dimmer?

V
vavalbel
Member
105
12-09-2019, 02:10 PM
#2
Which voltage are you asking about?
V
vavalbel
12-09-2019, 02:10 PM #2

Which voltage are you asking about?

_
_ParanormaL
Junior Member
8
12-09-2019, 02:24 PM
#3
4 Simms or 2? It's a quick setup, which isn't too surprising given the speed is a bit lower.
_
_ParanormaL
12-09-2019, 02:24 PM #3

4 Simms or 2? It's a quick setup, which isn't too surprising given the speed is a bit lower.

B
blacknight388
Junior Member
32
12-13-2019, 05:20 PM
#4
4
B
blacknight388
12-13-2019, 05:20 PM #4

4

9
992x
Senior Member
506
12-13-2019, 11:56 PM
#5
Bios indicates maximum 1.35v
9
992x
12-13-2019, 11:56 PM #5

Bios indicates maximum 1.35v

B
Blaster12121
Member
155
12-14-2019, 01:44 AM
#6
It's simple to increase the voltage to 1.45v without any active cooling.
B
Blaster12121
12-14-2019, 01:44 AM #6

It's simple to increase the voltage to 1.45v without any active cooling.

A
alejandrobo1
Posting Freak
877
12-14-2019, 03:28 AM
#7
Absolutely, at 3600 it puts a lot of strain on the IMC and interconnect. You might want to manually adjust the SOC to 1.1 and DRAM to 1.35, then switch to 3200 with XMP/DOCP enabled. If that works, try it at 3600 as well.
A
alejandrobo1
12-14-2019, 03:28 AM #7

Absolutely, at 3600 it puts a lot of strain on the IMC and interconnect. You might want to manually adjust the SOC to 1.1 and DRAM to 1.35, then switch to 3200 with XMP/DOCP enabled. If that works, try it at 3600 as well.

M
200
12-27-2019, 01:21 AM
#8
It's likely higher voltage could boost the claimed performance, but I haven't seen a setup that maintained stability with just XMP/AMP settings.
M
monsterman1108
12-27-2019, 01:21 AM #8

It's likely higher voltage could boost the claimed performance, but I haven't seen a setup that maintained stability with just XMP/AMP settings.

P
PinkTacoSheep
Junior Member
16
01-07-2020, 07:57 AM
#9
Using four DRAM modules increases the pressure on the Integrated Memory Controller (IMC) relative to two. Although your system might support DDR4-3600+, the CPU's IMC may not be equipped to manage it.
P
PinkTacoSheep
01-07-2020, 07:57 AM #9

Using four DRAM modules increases the pressure on the Integrated Memory Controller (IMC) relative to two. Although your system might support DDR4-3600+, the CPU's IMC may not be equipped to manage it.