F5F Stay Refreshed Hardware Desktop Issue with RAM, please clarify!

Issue with RAM, please clarify!

Issue with RAM, please clarify!

R
Rinusvandijk
Member
141
11-13-2020, 08:43 PM
#1
Hi there, it seems your system displays a different speed than what you installed. This could happen if BIOS settings or RAM timings were changed after installation. Double-check the RAM type and ensure it matches the specifications. If the issue persists, revisit the BIOS configuration to confirm the correct values.
R
Rinusvandijk
11-13-2020, 08:43 PM #1

Hi there, it seems your system displays a different speed than what you installed. This could happen if BIOS settings or RAM timings were changed after installation. Double-check the RAM type and ensure it matches the specifications. If the issue persists, revisit the BIOS configuration to confirm the correct values.

C
Cute_Ari
Member
68
11-14-2020, 02:38 AM
#2
Ensure the switch labeled "XMP: Disabled" is chosen, then pick the corresponding XMP profile such as "3200 C16-18-18-36".
C
Cute_Ari
11-14-2020, 02:38 AM #2

Ensure the switch labeled "XMP: Disabled" is chosen, then pick the corresponding XMP profile such as "3200 C16-18-18-36".

I
ItzHayds_
Member
119
11-14-2020, 03:59 AM
#3
Today felt a bit more puzzling? =) The FakeKGB mentioned setting X.M.P. to enabled on your screenshot.
I
ItzHayds_
11-14-2020, 03:59 AM #3

Today felt a bit more puzzling? =) The FakeKGB mentioned setting X.M.P. to enabled on your screenshot.

A
alerabbit
Posting Freak
840
11-20-2020, 06:06 AM
#4
XMP serves as an overclocking setup, with 3200 being the maximum brightness level supported. This is the reason you must turn it on, since the device won’t automatically reach that speed when installed.
A
alerabbit
11-20-2020, 06:06 AM #4

XMP serves as an overclocking setup, with 3200 being the maximum brightness level supported. This is the reason you must turn it on, since the device won’t automatically reach that speed when installed.

G
GaymerTommy21
Member
152
11-20-2020, 01:55 PM
#5
XMP is already active. It seems the picture existed prior to that. I found various different values scattered throughout. The DRAM status displayed 2133, while the "Memory:" section showed another number. I adjusted a few parameters to 3200 and then turned on XMP before saving. The image in my first post was likely before those tweaks. These pictures display the present configurations.
G
GaymerTommy21
11-20-2020, 01:55 PM #5

XMP is already active. It seems the picture existed prior to that. I found various different values scattered throughout. The DRAM status displayed 2133, while the "Memory:" section showed another number. I adjusted a few parameters to 3200 and then turned on XMP before saving. The image in my first post was likely before those tweaks. These pictures display the present configurations.

R
rafinha_moraes
Member
189
11-20-2020, 02:38 PM
#6
It confirms the system is operating at 3200, everything appears fine. The 2133 value seems fixed in the code.
R
rafinha_moraes
11-20-2020, 02:38 PM #6

It confirms the system is operating at 3200, everything appears fine. The 2133 value seems fixed in the code.

S
sixpar
Member
137
11-20-2020, 05:37 PM
#7
I believe the system is capped at 2133 only in BIOS settings. Try launching Windows and check the Performance tab under Memory for speeds around 3200MHz. Your current reading is 2667, likely due to B460 architecture but intended to highlight the correct range.
S
sixpar
11-20-2020, 05:37 PM #7

I believe the system is capped at 2133 only in BIOS settings. Try launching Windows and check the Performance tab under Memory for speeds around 3200MHz. Your current reading is 2667, likely due to B460 architecture but intended to highlight the correct range.

I
iiSweeTzz
Posting Freak
862
11-20-2020, 06:31 PM
#8
It shows 3200, which suggests it's likely functioning, though the BIOS might be having trouble reading or showing it as Kilrah pointed out.
I
iiSweeTzz
11-20-2020, 06:31 PM #8

It shows 3200, which suggests it's likely functioning, though the BIOS might be having trouble reading or showing it as Kilrah pointed out.