I pushed my PC's overclocking too far and it's not starting. Need help!

F5F Stay Refreshed Power Users Overclocking I pushed my PC's overclocking too far and it's not starting. Need help!

Pages (3): Previous 1 2 3 Next

SchoolToilet
Junior Member

09-12-2022, 10:10 PM

#11

Do you not have a screwdriver?

SchoolToilet

09-12-2022, 10:10 PM #11

Do you not have a screwdriver?

ThorTheFirst
Junior Member

09-19-2022, 12:49 PM

#12

Did you find the visible CMOS connections on the motherboard? Check your guide or inspect the board. It should mention "CLR CMOS." My unit is situated at the very base of the board.

ThorTheFirst

09-19-2022, 12:49 PM #12

Did you find the visible CMOS connections on the motherboard? Check your guide or inspect the board. It should mention "CLR CMOS." My unit is situated at the very base of the board.

Ks34_MisteR
Member

245

09-21-2022, 04:53 AM

#13

I understand the pins, but I'm unsure how to use a screwdriver (I have one).

Ks34_MisteR

09-21-2022, 04:53 AM #13

I understand the pins, but I'm unsure how to use a screwdriver (I have one).

Grimm_E
Member

103

09-21-2022, 12:38 PM

#14

When the machine is powered down, lightly press the screwdriver onto both pins simultaneously for a short duration. After that, restart the computer.

Grimm_E

09-21-2022, 12:38 PM #14

When the machine is powered down, lightly press the screwdriver onto both pins simultaneously for a short duration. After that, restart the computer.

MegaDisco
Senior Member

352

09-23-2022, 02:18 PM

#15

House and carkeys connect the two pins shown in the picture. Remember to disconnect the power cord while doing it.

MegaDisco

09-23-2022, 02:18 PM #15

House and carkeys connect the two pins shown in the picture. Remember to disconnect the power cord while doing it.

Meezar
Junior Member

09-23-2022, 03:04 PM

#16

And how do you confirm you got it correct? You used a paper clip and a screwdriver but still got no response: no signal.

Meezar

09-23-2022, 03:04 PM #16

And how do you confirm you got it correct? You used a paper clip and a screwdriver but still got no response: no signal.

XknockMC
Member

121

09-25-2022, 04:00 PM

#17

I didn't overclock the CPU and RAM myself. I used a BIOS update to adjust settings, and the RAM is DDR4 3200MHz.

XknockMC

09-25-2022, 04:00 PM #17

I didn't overclock the CPU and RAM myself. I used a BIOS update to adjust settings, and the RAM is DDR4 3200MHz.

Jarzzermann
Posting Freak

788

10-01-2022, 11:43 PM

#18

I increased the clock speed of both the CPU and RAM in the BIOS.
I have a Corsair Vengeance 8 GB 2400 MHz with just one PCIe slot.

Jarzzermann

10-01-2022, 11:43 PM #18

I increased the clock speed of both the CPU and RAM in the BIOS.
I have a Corsair Vengeance 8 GB 2400 MHz with just one PCIe slot.

ReborntoKill
Posting Freak

821

10-03-2022, 04:24 PM

#19

It seems you're having trouble accessing BIOS settings and suspect potential damage while attempting to adjust RAM speeds. You're also checking for any audible signals during the boot process.

ReborntoKill

10-03-2022, 04:24 PM #19

It seems you're having trouble accessing BIOS settings and suspect potential damage while attempting to adjust RAM speeds. You're also checking for any audible signals during the boot process.

bluehypergiant
Member

220

10-11-2022, 12:54 PM

#20

I don't have a mobile speaker. However, when I attempt to start the PC, the "not detecting cpu" indicator appears. I can't access BIOS because the computer won't open at all. The monitor shows "no signal" and then shuts off, though the fans are still running.

bluehypergiant

10-11-2022, 12:54 PM #20

Pages (3): Previous 1 2 3 Next