I increased my CPU speed to 5Ghz but now I can't...
I increased my CPU speed to 5Ghz but now I can't...
Adjust the voltage in increments of 0.05V until it stabilizes, aiming for a maximum of 1.4V vcore.
I tried 5Ghz with 1.4V vcore but kept experiencing crashes and a blue screen after using Aida 64 to stress the CPU.
Honestly, I’d prefer to take the card back to MSI and return the Gigabyte.
Why? I invested a lot of money on this motherboard.
Adjust the voltage in increments of 0.05V until stable, aiming for a maximum of 1.4V vcore.
I tested 5Ghz with 1.4V vcore but still experienced crashes and a blue screen after stressing the CPU using Aida 64.
Honestly, I’d consider returning the motherboard or sending it back with Gigabyte. If the BIOS is updated, temperatures and voltages seem normal, yet stability remains an issue even on a newer board. It might point to a hardware problem that only Gigabyte can resolve.
Was es korrekt gesichert, dass der 8-Pin-CPU-Anschluss an der Motherboard angeschlossen wurde?
Adjust the voltage in increments of 0.05V until stable, aiming for a maximum of 1.4V vcore.
I tried 5Ghz with 1.4V vcore but kept experiencing crashes and a blue screen after using Aida 64 to stress the CPU.
Honestly, I’d go back to MSI and return the Gigabyte.
Why? I invested a lot in this motherboard.
Did you verify that the 8-pin CPU connector was properly attached on the motherboard? I'm not entirely sure if someone assembled my PC, but it seems likely they did. These connections need to be linked to the PSU for overclocking both the 4-pin and 8-pin CPUs.
Did you verify that the 8-pin CPU connector was properly attached on the motherboard? I'm not entirely sure if someone built my PC, but I think they did. These must be linked to the PSU to enable overclocking for both the 4-pin and 8-pin CPUs. Holy crap, there seems to be only the 8-pin connected while the 4-pins aren't, can I connect them myself? And where can I find this 4-pin cable?
Verify your PSU cables, there should be a 4-pin link marked for CPU or labeled ATX. Likely, the person who assembled the system didn't connect it to the PSU, so it's probably inside the case. It's straightforward to set up, so you should manage it yourself.
Review your PSU cables, there should be that 4-pin connection labeled for CPU or ATX. It's likely the system wasn't connected to the PSU properly, so it probably came in the box. It’s quite simple to set up, and you should be able to do it yourself.
The appearance might be an 8-pin connection, but it should be configured as two separate 4-pin connections.
Now I need to get a 4-pin connector from the box and connect it from the PSU to the top left CPU connector? I’m not sure if there’s enough space in the PSU to add more cables, or maybe I can find an 8+4 pin connector and use that instead of the current 8-pin setup. Or perhaps there isn’t an 8+4 pin available at all?
encise :
WildCard999 :
encise :
WildCard999 :
Did you make sure you connected the 8-pin CPU connector on the motherboard?
I'm not sure someone build my pc, but i guess yes he did
These
must
be connected to the PSU to overclock that CPU, both the 4-pin and 8-pin.
Holy crap , there is only the 8-pin connected, the 4-pins is not connected, can i connect it by my self?, and how can i get this 4-pin cable?
Your PSU should have a 4 pin connector. Just line up the connector, you'll see a clip and something for the clip to snap onto on the outside of the connector. It will only fit one way.
If you have doubts take a picture and we will tell you if it is lined up correctly.