F5F Stay Refreshed Hardware Desktop How to use xmp with 4 sticks of DDR5?

How to use xmp with 4 sticks of DDR5?

How to use xmp with 4 sticks of DDR5?

Pages (2): Previous 1 2
T
tiamat0913
Junior Member
4
03-01-2022, 05:05 AM
#11
haven't tested it with two dimmers yet, but i think it could work. If speed matters more than capacity, i might go with 32gb and discard the other two dimmers.
T
tiamat0913
03-01-2022, 05:05 AM #11

haven't tested it with two dimmers yet, but i think it could work. If speed matters more than capacity, i might go with 32gb and discard the other two dimmers.

G
GrinningTube
Member
185
03-01-2022, 12:21 PM
#12
Yep. 32GB is plenty and speed over capacity at 32GB++ for gaming Check the video above
G
GrinningTube
03-01-2022, 12:21 PM #12

Yep. 32GB is plenty and speed over capacity at 32GB++ for gaming Check the video above

B
Barney_420
Member
72
03-01-2022, 12:33 PM
#13
Thank you all very much; your assistance was invaluable.
B
Barney_420
03-01-2022, 12:33 PM #13

Thank you all very much; your assistance was invaluable.

A
amyeenhoorn
Member
121
03-02-2022, 08:54 AM
#14
We're here to assist whenever you require further support. Just let us know where you need help writing.
A
amyeenhoorn
03-02-2022, 08:54 AM #14

We're here to assist whenever you require further support. Just let us know where you need help writing.

B
BlackAce_44
Member
52
03-02-2022, 02:40 PM
#15
When configuring manual speeds for DDR5, it's generally recommended to keep XMP/EXPO activated. This allows the board to automatically optimize settings beyond just voltage, ensuring better performance. For DDR4, manual frequency and DRAM voltage adjustments were often sufficient. With DDR5, skipping these features requires direct configuration on the motherboard, and you may need to consult overclocking manuals to fine-tune parameters. The maximum supported speed for four 16GB sticks in a Zen 4 system is 3600 MHz, though pushing it further demands careful button selection.
B
BlackAce_44
03-02-2022, 02:40 PM #15

When configuring manual speeds for DDR5, it's generally recommended to keep XMP/EXPO activated. This allows the board to automatically optimize settings beyond just voltage, ensuring better performance. For DDR4, manual frequency and DRAM voltage adjustments were often sufficient. With DDR5, skipping these features requires direct configuration on the motherboard, and you may need to consult overclocking manuals to fine-tune parameters. The maximum supported speed for four 16GB sticks in a Zen 4 system is 3600 MHz, though pushing it further demands careful button selection.

T
Thuthur
Member
191
03-02-2022, 03:59 PM
#16
Absolutely, having over 32GB isn't important here.
T
Thuthur
03-02-2022, 03:59 PM #16

Absolutely, having over 32GB isn't important here.

H
helenma0301
Senior Member
250
03-03-2022, 01:49 PM
#17
Grab the RAM sticks and order a standard 2x32 setup. Avoid the 4-stick version since it tends to fail early. This should work smoothly even with demanding games like modded Minecraft.
H
helenma0301
03-03-2022, 01:49 PM #17

Grab the RAM sticks and order a standard 2x32 setup. Avoid the 4-stick version since it tends to fail early. This should work smoothly even with demanding games like modded Minecraft.

A
arcadekk
Junior Member
37
03-03-2022, 02:56 PM
#18
Since its launch, owning this platform has become a lot simpler. I’ve applied over 15 BIOS updates to my single motherboard since then. It’s not the same as when it first came out.
A
arcadekk
03-03-2022, 02:56 PM #18

Since its launch, owning this platform has become a lot simpler. I’ve applied over 15 BIOS updates to my single motherboard since then. It’s not the same as when it first came out.

Pages (2): Previous 1 2