How to link a device to a distant computer using an Ethernet connection?
How to link a device to a distant computer using an Ethernet connection?
I am attempting to link to a distant machine connected through a router, using an Ethernet cable that passes through PVC pipe. The cables are positioned about 150 feet away and consist of four strands. After turning on the remote device and trying to establish a WiFi connection with other machines, I receive a notification that it cannot be located. I tested it on two different devices—a Windows 10 Pro Surface and a Linux 24.04 Dell XPS. The router shows no activity on the port where the cable is connected. I restarted both the remote machine and the router without success. I verified the cables for continuity, confirmed they are intact. I replaced two cables and the inline coupler, but the issue persists. This is my third or fourth attempt in roughly three to four weeks. Recent heavy rain might be a factor. I’m uncertain what to do next. Any assistance would be greatly appreciated. Thank you.
The labels on the Ethernet cables inside the PVC pipes are unclear. Many fake cables are sold and used, while some genuine ones are improperly routed and connected.
On which side is the "wifi" connection located? For instance, in a diagram where ----> stands for an Ethernet cable:
PC----> [LAN port] Router [LAN port]
Ethernet cables inside 150' PVC pipe ----> [LAN port] Remote PC
Would you like me to adjust or clarify your diagram?
More information needed.
Completely avoid using couplers. Opt for long burial grade Ethernet cables directly instead of relying on them with couplers to create extended cables.
I see it as four distinct, parallel cables instead of four shorter ones linked with couplers.
Strongly agree with the "no couplers" and burial grade cables suggestion.
That means all copper, 22-24 AWG, UTP.
Also, for underground use, UV protection is irrelevant.
Same applies to pre-installed, snag-free RJ45 connectors.
Not suitable if the cable is being pulled.
If buried directly, ends need patch panel termination as I understand.
Even then, I remain cautious about any product claims or advertisements.
Yeah, it should be all copper. I looked it up quickly and didn’t read thoroughly.
Pure copper.
https://www.amazon.com/GearIT-Cat6-Outdo...6RZY/?th=1
In theory it should be terminated, but the person might not have the right tools, skills, or time.
Direct burial also means he doesn’t need to use a PVC pipe. But it should be deep enough so gardening work won’t accidentally harm the cable.
You may utilize standard indoor cable within PVC pipes; outdoor or direct burial cables are not required. This setup requires Cat5e, pure copper wire with a size of 22-24. The conduit offers protection against physical damage, though it is generally more expensive, which is why most new installations opt for direct burial cables. When extending the distance, adhering to standards becomes crucial. There is a large quantity of counterfeit cables available. Flat cables are the most prevalent, but they are typically limited to shorter ranges, allowing sellers to market them accordingly. Copper-clad aluminum wire is also widely used, particularly in fake outdoor cables. The pipe should be sufficiently wide if inline splices or couplers are involved. Using multiple short cables is discouraged as each splice increases resistance and reduces effective distance. Ethernet cables are rated for up to 300 feet (100 meters) in a single run; I have not encountered specifications detailing performance with couplers. It is typical to find patch panels or wall jacks at each end, which can accommodate some splicing, but I recommend avoiding this approach.
Router (wifi) [LAN port] ----
150'
PVC pipe cables connected via coupler to LAN port, leading to a remote PC.
Only the cables and coupler remain along the route.
I crafted the Ethernet spools myself due to required length and quantity.
Four spools provide redundancy and future flexibility—easier cable swapping if needed.
Burial-grade cable wasn’t necessary inside the PVC conduit, though I might reconsider later.
One coupler sits between the last 25' segment and the four 150' cables, all housed within the conduit.
The conduit ends are protected from moisture due to sheltered positioning.
This is my first attempt at connecting in a while; recently I’ve faced minimal issues linking to the remote PC.
So precisely where wifi is connected? What equipment is available at the remote location?
If there are four cables inside the PVC conduit, why only one coupler? You don't require all four, at most two (one for backup), and using a switch or AP at the remote site would suffice.
Again, I'll completely avoid using couplers.