F5F Stay Refreshed Hardware Desktop Device not functioning properly.

Device not functioning properly.

Device not functioning properly.

Pages (2): Previous 1 2
I
IsHoEuEr
Junior Member
3
09-03-2021, 01:16 PM
#11
Aligning the rear IO allows you to lower the board into the back of the case. You can push the right side down further, and as the screws begin to engage, it descends. The board bends slightly, resulting in an unappealing appearance.
I
IsHoEuEr
09-03-2021, 01:16 PM #11

Aligning the rear IO allows you to lower the board into the back of the case. You can push the right side down further, and as the screws begin to engage, it descends. The board bends slightly, resulting in an unappealing appearance.

A
Altone123
Member
62
09-23-2021, 01:59 AM
#12
Are these risers ready? They're already in progress, and I messed up the board setup.
A
Altone123
09-23-2021, 01:59 AM #12

Are these risers ready? They're already in progress, and I messed up the board setup.

S
Smooth_Scott
Junior Member
2
09-23-2021, 01:08 PM
#13
S
Smooth_Scott
09-23-2021, 01:08 PM #13

R
ReakZ_
Member
183
10-12-2021, 10:14 PM
#14
Use a screwdriver to press the tip onto the power switch pin. It shouldn't affect the PSU connected to the motherboard. Also, check if the PSU is turning on.
R
ReakZ_
10-12-2021, 10:14 PM #14

Use a screwdriver to press the tip onto the power switch pin. It shouldn't affect the PSU connected to the motherboard. Also, check if the PSU is turning on.

V
Valinax
Junior Member
21
10-13-2021, 04:24 AM
#15
This video demonstrates how to short the power switch outside a case. If the setup works properly, does it have a PSU that you can remove another PC from to test whether it switches the MB on?
V
Valinax
10-13-2021, 04:24 AM #15

This video demonstrates how to short the power switch outside a case. If the setup works properly, does it have a PSU that you can remove another PC from to test whether it switches the MB on?

K
kevin2010
Member
108
10-14-2021, 12:22 PM
#16
I don’t have another PSU. I believe I’ll stop here for now. My friend mentioned he’ll visit tomorrow to check it out. Thanks for your assistance!
K
kevin2010
10-14-2021, 12:22 PM #16

I don’t have another PSU. I believe I’ll stop here for now. My friend mentioned he’ll visit tomorrow to check it out. Thanks for your assistance!

S
SpinnSky
Member
73
10-14-2021, 01:54 PM
#17
Remove all parts and the breadboard from the case. This is the simplest way to check if something is dead or if it was added during installation into the chassis. Breadboarding refers to assembling the PC outside the case, which is useful before doing any case preparation—it really helps save time and is valuable in electrical engineering.
S
SpinnSky
10-14-2021, 01:54 PM #17

Remove all parts and the breadboard from the case. This is the simplest way to check if something is dead or if it was added during installation into the chassis. Breadboarding refers to assembling the PC outside the case, which is useful before doing any case preparation—it really helps save time and is valuable in electrical engineering.

N
Nunooh
Member
181
10-18-2021, 05:44 AM
#18
I completed most of it outside. The only part I omitted was the GPU, so I wasn’t able to connect anything directly.
N
Nunooh
10-18-2021, 05:44 AM #18

I completed most of it outside. The only part I omitted was the GPU, so I wasn’t able to connect anything directly.

Pages (2): Previous 1 2