F5F Stay Refreshed Hardware Desktop B550 display turns dark unexpectedly after applying XMP profile.

B550 display turns dark unexpectedly after applying XMP profile.

B550 display turns dark unexpectedly after applying XMP profile.

Pages (3): 1 2 3 Next
M
MrCupquake
Member
Find
229
05-22-2020, 12:01 PM
#1
hi guys, can you please help me with my XMP issue? Problem : I purchased memories that support 3600MHz. After setting the XMP for this in the bios the system hangs up with black screen of death Specs MB: Gigabyte B550 Vision D url CPU : Ryzen 9 5900x RAM : Trident Z Neo DDR4-3600MHz CL16-19-19-39 1.35V 32GB (2x16GB) url can you help me figure out why doesn't the xmp work or how to do it manually?
Reply
Reply
M
MrCupquake
05-22-2020, 12:01 PM #1

hi guys, can you please help me with my XMP issue? Problem : I purchased memories that support 3600MHz. After setting the XMP for this in the bios the system hangs up with black screen of death Specs MB: Gigabyte B550 Vision D url CPU : Ryzen 9 5900x RAM : Trident Z Neo DDR4-3600MHz CL16-19-19-39 1.35V 32GB (2x16GB) url can you help me figure out why doesn't the xmp work or how to do it manually?

Reply
Reply
B
britek
Junior Member
Find
46
05-24-2020, 08:19 AM
#2
If you can't reach your BIOS, perform a CMOS reset. (Refer to your manual for specific steps regarding your graphics card.) Next, turn on XMP settings and then adjust the DRAM voltage to 1.45V manually. See if this resolves the issue.
Reply
Reply
B
britek
05-24-2020, 08:19 AM #2

If you can't reach your BIOS, perform a CMOS reset. (Refer to your manual for specific steps regarding your graphics card.) Next, turn on XMP settings and then adjust the DRAM voltage to 1.45V manually. See if this resolves the issue.

Reply
Reply
A
afonso9898
Member
Find
54
05-31-2020, 05:18 AM
#3
If the system won't boot and there are no POST sounds, reset the CMOS. Intel provides instructions for this, and AMD's setup is similar. Once the CMOS is reset, attempt to configure the settings manually by overclocking the RAM as specified in the manual.
Reply
Reply
A
afonso9898
05-31-2020, 05:18 AM #3

If the system won't boot and there are no POST sounds, reset the CMOS. Intel provides instructions for this, and AMD's setup is similar. Once the CMOS is reset, attempt to configure the settings manually by overclocking the RAM as specified in the manual.

Reply
Reply
Z
zombietony
Member
Find
55
06-01-2020, 07:47 AM
#4
It seems you're having trouble with a manual process. Can you clarify what you're trying to accomplish?
Reply
Reply
Z
zombietony
06-01-2020, 07:47 AM #4

It seems you're having trouble with a manual process. Can you clarify what you're trying to accomplish?

Reply
Reply
F
Fred10244
Posting Freak
Find
937
06-09-2020, 08:14 AM
#5
It seems the signal voltage might be the issue. You should check the DRDRVPP settings and termination configuration accordingly.
Reply
Reply
F
Fred10244
06-09-2020, 08:14 AM #5

It seems the signal voltage might be the issue. You should check the DRDRVPP settings and termination configuration accordingly.

Reply
Reply
P
ProTimmy
Member
Find
123
06-09-2020, 10:49 AM
#6
Avoid altering the DRAM voltage directly. Instead, adjust it gradually by 0.2 volts each time and monitor the results rather than relying on the default 1.45 volts setting.
Reply
Reply
P
ProTimmy
06-09-2020, 10:49 AM #6

Avoid altering the DRAM voltage directly. Instead, adjust it gradually by 0.2 volts each time and monitor the results rather than relying on the default 1.45 volts setting.

Reply
Reply
F
Freggel15
Junior Member
Find
4
06-15-2020, 06:54 AM
#7
But my method is adjusting it to 1.45V and checking performance, then reducing in small increments of 0.0125V until finding the most stable setting. It helps confirm functionality quickly at that level. Results vary by individual.
Reply
Reply
F
Freggel15
06-15-2020, 06:54 AM #7

But my method is adjusting it to 1.45V and checking performance, then reducing in small increments of 0.0125V until finding the most stable setting. It helps confirm functionality quickly at that level. Results vary by individual.

Reply
Reply
B
BlueBackChart
Member
Find
84
06-15-2020, 01:31 PM
#8
I chose 1.45V power. The system started up, though I don’t see any changes. My experience remains at 2140, even with XMP enabled and the BIOS indicating 1.45V memory.
Reply
Reply
B
BlueBackChart
06-15-2020, 01:31 PM #8

I chose 1.45V power. The system started up, though I don’t see any changes. My experience remains at 2140, even with XMP enabled and the BIOS indicating 1.45V memory.

Reply
Reply
A
Athame_
Senior Member
Find
734
06-24-2020, 03:38 PM
#9
Did you mean a specific number or phrase? Let me know so I can clarify.
Reply
Reply
A
Athame_
06-24-2020, 03:38 PM #9

Did you mean a specific number or phrase? Let me know so I can clarify.

Reply
Reply
B
Barney_420
Member
Find
72
06-26-2020, 04:31 AM
#10
Sure, that makes sense. I'm not great at keeping track of CPU or memory speeds, so I assume the current setup is still at 2133 MHz. The aim is to boost it to around 3600 MHz. XMP is already enabled, and the voltage is set to 1.45, which works fine—system boots at 1.35 as well, though speed isn't improving.
Reply
Reply
B
Barney_420
06-26-2020, 04:31 AM #10

Sure, that makes sense. I'm not great at keeping track of CPU or memory speeds, so I assume the current setup is still at 2133 MHz. The aim is to boost it to around 3600 MHz. XMP is already enabled, and the voltage is set to 1.45, which works fine—system boots at 1.35 as well, though speed isn't improving.

Reply
Reply
Pages (3): 1 2 3 Next