F5F Stay Refreshed Hardware Desktop A new integrated graphics PC model hits 100C and powers down.

A new integrated graphics PC model hits 100C and powers down.

A new integrated graphics PC model hits 100C and powers down.

Pages (2): 1 2 Next
P
P1NG3S
Member
50
07-20-2022, 08:38 PM
#1
Hello everyone, I just built my PC without a GPU yet it boots into BIOS. Inside BIOS, the CPU temperatures spike to 100 degrees and the system shuts down quickly. I’ve confirmed everything is installed correctly, including the AIO cooler, which is working fine and the tubes are warm when active. My processor is an AMD Ryzen 7 7700X, the motherboard is B650 Aorus Elite AX, and the cooler is the Icue H115i Elite Capellix XT 280mm. If anyone has any ideas on how to resolve this issue, it would be really helpful.
P
P1NG3S
07-20-2022, 08:38 PM #1

Hello everyone, I just built my PC without a GPU yet it boots into BIOS. Inside BIOS, the CPU temperatures spike to 100 degrees and the system shuts down quickly. I’ve confirmed everything is installed correctly, including the AIO cooler, which is working fine and the tubes are warm when active. My processor is an AMD Ryzen 7 7700X, the motherboard is B650 Aorus Elite AX, and the cooler is the Icue H115i Elite Capellix XT 280mm. If anyone has any ideas on how to resolve this issue, it would be really helpful.

V
vuji1
Junior Member
2
07-21-2022, 04:48 AM
#2
Both tubes being warm indicates a problem since it shouldn't be cooling properly. Continuing without action could lead to overheating, and heating the water might be necessary.
V
vuji1
07-21-2022, 04:48 AM #2

Both tubes being warm indicates a problem since it shouldn't be cooling properly. Continuing without action could lead to overheating, and heating the water might be necessary.

R
RHINOncg2000
Member
162
07-26-2022, 05:37 PM
#3
It seems the device is either overheating or experiencing a hardware issue.
R
RHINOncg2000
07-26-2022, 05:37 PM #3

It seems the device is either overheating or experiencing a hardware issue.

W
wesselboy11
Member
221
07-26-2022, 06:47 PM
#4
Only a single tube is warm, and without any action it rapidly reaches 100°C in the BIOS before stopping.
W
wesselboy11
07-26-2022, 06:47 PM #4

Only a single tube is warm, and without any action it rapidly reaches 100°C in the BIOS before stopping.

N
NottaSpy
Member
232
07-26-2022, 07:00 PM
#5
It might be happening because the integrated graphics are causing extra heat. You could reduce your CPU's performance in BIOS to help manage temperatures.
N
NottaSpy
07-26-2022, 07:00 PM #5

It might be happening because the integrated graphics are causing extra heat. You could reduce your CPU's performance in BIOS to help manage temperatures.

R
RJScience
Junior Member
14
07-26-2022, 07:41 PM
#6
The issue isn't related to the iGPU.
R
RJScience
07-26-2022, 07:41 PM #6

The issue isn't related to the iGPU.

E
EisTeeKlaus
Senior Member
490
08-02-2022, 03:54 PM
#7
Confirm your cooler is functioning properly.
E
EisTeeKlaus
08-02-2022, 03:54 PM #7

Confirm your cooler is functioning properly.

K
Kewan85
Junior Member
3
08-02-2022, 11:55 PM
#8
It might simply be that it isn't large enough.
K
Kewan85
08-02-2022, 11:55 PM #8

It might simply be that it isn't large enough.

H
hontzy
Junior Member
3
08-03-2022, 12:04 AM
#9
Disagree with that assessment. The cooler should suffice, and even if it's too small, the CPU wouldn't reach 100°F instantly on the BIOS screen. There must be an issue with your setup. When you say you "double checked," are you removing the cooler from the CPU and verifying the thermal paste adhesion? I've tried unmounted air tower coolers placed directly on the CPU without fans to test performance before full load—any good thermal interface needs time to stabilize. I’d take a fresh start just to confirm.
H
hontzy
08-03-2022, 12:04 AM #9

Disagree with that assessment. The cooler should suffice, and even if it's too small, the CPU wouldn't reach 100°F instantly on the BIOS screen. There must be an issue with your setup. When you say you "double checked," are you removing the cooler from the CPU and verifying the thermal paste adhesion? I've tried unmounted air tower coolers placed directly on the CPU without fans to test performance before full load—any good thermal interface needs time to stabilize. I’d take a fresh start just to confirm.

A
Admiralfiggins
Member
211
08-03-2022, 12:51 AM
#10
i don't trust preinstalled thermal compound, so i would remove it and add fresh out of the tube. make an X on your cpu, the ricegrain is too little now. ... on the other hand.. i don't trust AIO's.. but that's another topic EDIT: and never mix preinstalled thermal compound and thermal paste..
A
Admiralfiggins
08-03-2022, 12:51 AM #10

i don't trust preinstalled thermal compound, so i would remove it and add fresh out of the tube. make an X on your cpu, the ricegrain is too little now. ... on the other hand.. i don't trust AIO's.. but that's another topic EDIT: and never mix preinstalled thermal compound and thermal paste..

Pages (2): 1 2 Next