You're experiencing issues with your new PC's RAM performance. Let's troubleshoot together.

F5F Stay Refreshed Hardware Desktop You're experiencing issues with your new PC's RAM performance. Let's troubleshoot together.

You're experiencing issues with your new PC's RAM performance. Let's troubleshoot together.

You're experiencing issues with your new PC's RAM performance. Let's troubleshoot together.

K

KlayDog1
Senior Member

685

01-14-2021, 10:03 AM

#1

Hello everyone, I just purchased a prebuilt system from Skytech Gaming. Unfortunately, the RAM I received is rated for 3200 MHz and doesn’t match my Corsair Vengeance RGB RAM which also supports that speed. My PC runs an i5 12600K on an ASRock B660M-C motherboard. I’ve updated the BIOS to the latest version but it still won’t boot properly—when I enable XMP and set the correct speed, it keeps restarting. I’ve also experimented with adjusting the RAM voltage, but that didn’t help either. Any advice would be greatly appreciated.

K

KlayDog1

01-14-2021, 10:03 AM #1

Hello everyone, I just purchased a prebuilt system from Skytech Gaming. Unfortunately, the RAM I received is rated for 3200 MHz and doesn’t match my Corsair Vengeance RGB RAM which also supports that speed. My PC runs an i5 12600K on an ASRock B660M-C motherboard. I’ve updated the BIOS to the latest version but it still won’t boot properly—when I enable XMP and set the correct speed, it keeps restarting. I’ve also experimented with adjusting the RAM voltage, but that didn’t help either. Any advice would be greatly appreciated.

X

XxBOMB_BAxX
Member

70

01-14-2021, 06:37 PM

#2

Adjust settings automatically based on the specified parameters.

X

XxBOMB_BAxX

01-14-2021, 06:37 PM #2

Adjust settings automatically based on the specified parameters.

N

Natan_Rtz
Junior Member

27

01-20-2021, 01:21 PM

#3

This seems to not be functioning as intended.

N

Natan_Rtz

01-20-2021, 01:21 PM #3

This seems to not be functioning as intended.

A

A7mad_a33
Junior Member

20

01-28-2021, 02:36 PM

#4

Increase the voltage step by step, up to a maximum of 1.45 volts.

A

A7mad_a33

01-28-2021, 02:36 PM #4

Increase the voltage step by step, up to a maximum of 1.45 volts.

A

Azumia
Junior Member

11

01-29-2021, 07:36 PM

#5

There is still nothing.

A

Azumia

01-29-2021, 07:36 PM #5

There is still nothing.

T

TheDark245
Member

125

02-18-2021, 03:20 PM

#6

The default speed without OCR is board-specific. You might want to check the ASRock forum for more details.

T

TheDark245

02-18-2021, 03:20 PM #6

The default speed without OCR is board-specific. You might want to check the ASRock forum for more details.

H

HellNether
Senior Member

731

02-19-2021, 09:44 AM

#7

Reach out to SkyTech for assistance.

H

HellNether

02-19-2021, 09:44 AM #7

Reach out to SkyTech for assistance.

_

_ErikThePanda_
Posting Freak

807

02-19-2021, 10:28 AM

#8

It’s my strategy for tomorrow, though I’m hoping they’ll address the problem

_

_ErikThePanda_

02-19-2021, 10:28 AM #8

It’s my strategy for tomorrow, though I’m hoping they’ll address the problem

C

commander_mais
Member

195

02-20-2021, 01:41 AM

#9

They should, as the spec mentioned this board comes with a standard 3200MHz if that's correct.

C

commander_mais

02-20-2021, 01:41 AM #9

They should, as the spec mentioned this board comes with a standard 3200MHz if that's correct.