Your RAM's CAS latency is configured at 1 nanoseconds.

Pages (3): Previous 1 2 3 Next

MikeDragon159
Senior Member

661

08-29-2016, 05:56 PM

#11

It seems the setup is indeed unstable. You might consider slightly increasing the voltage.

MikeDragon159

08-29-2016, 05:56 PM #11

It seems the setup is indeed unstable. You might consider slightly increasing the voltage.

nep24
Member

224

08-31-2016, 07:55 PM

#12

You'd just need to adjust the DRAM voltage in the BIOS. Changing it alone typically won't damage your system unless there are underlying issues.

nep24

08-31-2016, 07:55 PM #12

You'd just need to adjust the DRAM voltage in the BIOS. Changing it alone typically won't damage your system unless there are underlying issues.

KablooieKablam
Posting Freak

908

08-31-2016, 08:10 PM

#13

The frequency is adjusted to 100.27MHz instead of 100MHz.

KablooieKablam

08-31-2016, 08:10 PM #13

The frequency is adjusted to 100.27MHz instead of 100MHz.

opticgunship
Posting Freak

815

08-31-2016, 09:08 PM

#14

Check the specifications for your device's maximum voltage requirements. If your XMP profile adjusts automatically to around 1.35V and you're aiming for up to 1.36V, that’s ideal. For safety, stick to a 1.4V limit.

opticgunship

08-31-2016, 09:08 PM #14

2__PAC
Junior Member

09-02-2016, 02:51 PM

#15

Yes, it helps.

2__PAC

09-02-2016, 02:51 PM #15

Yes, it helps.

joeyman108
Member

09-02-2016, 10:52 PM

#16

The display does not reflect 100.27MHz, only 100MHz is visible.

joeyman108

09-02-2016, 10:52 PM #16

The display does not reflect 100.27MHz, only 100MHz is visible.

xalie305
Junior Member

09-10-2016, 02:57 AM

#17

It doesn't specify your maximum voltage, but it outlines the suggested settings. I recommend turning on xmp, setting the voltage to 1.36, and checking the results.

xalie305

09-10-2016, 02:57 AM #17

It doesn't specify your maximum voltage, but it outlines the suggested settings. I recommend turning on xmp, setting the voltage to 1.36, and checking the results.

Glumanday
Junior Member

09-10-2016, 06:43 AM

#18

It's 100.29 in the first image of the CPU statistics section.

Glumanday

09-10-2016, 06:43 AM #18

It's 100.29 in the first image of the CPU statistics section.

qabooch
Junior Member

09-10-2016, 12:45 PM

#19

I switched it to 100Mhz now.

qabooch

09-10-2016, 12:45 PM #19

I switched it to 100Mhz now.

Kapodistrias
Member

130

09-17-2016, 11:45 AM

#20

I activated XMP and adjusted the RAM to 3600Mhz. The voltage was changed from auto to 1.350 volts. That image was for 3200Mhz, so I’m checking if 1.350 volts works at 3600Mhz.

Kapodistrias

09-17-2016, 11:45 AM #20

I activated XMP and adjusted the RAM to 3600Mhz. The voltage was changed from auto to 1.350 volts. That image was for 3200Mhz, so I’m checking if 1.350 volts works at 3600Mhz.

Pages (3): Previous 1 2 3 Next