F5F Stay Refreshed Hardware Desktop Windows 11 PC experiences sudden freezes?

Windows 11 PC experiences sudden freezes?

Windows 11 PC experiences sudden freezes?

Pages (3): Previous 1 2 3 Next
S
sydneyyyyyy
Senior Member
396
07-31-2021, 02:39 AM
#11
Updating the power settings to "High performance" didn't fix the issue. It froze just ten minutes ago. The only remaining choice is to remove one RAM stick and check if the freezing occurs. I'll keep you updated on any developments.
S
sydneyyyyyy
07-31-2021, 02:39 AM #11

Updating the power settings to "High performance" didn't fix the issue. It froze just ten minutes ago. The only remaining choice is to remove one RAM stick and check if the freezing occurs. I'll keep you updated on any developments.

X
xXEHaytonXx
Junior Member
11
08-02-2021, 03:26 AM
#12
What ram settings are you using?
Can you show screenshots from CPU-Z - memory and spd sections?
(upload to imgur.com and post link)
Are you using PCIE riser cable?
You may want to try forcing PCIE slot into PCIE 3.0 mode.
X
xXEHaytonXx
08-02-2021, 03:26 AM #12

What ram settings are you using?
Can you show screenshots from CPU-Z - memory and spd sections?
(upload to imgur.com and post link)
Are you using PCIE riser cable?
You may want to try forcing PCIE slot into PCIE 3.0 mode.

M
Muezzze
Member
60
08-03-2021, 11:45 PM
#13
Here are the 3 screenshots provided.
Check them out: https://imgur.com/a/p3mDlik
View: https://imgur.com/a/p3mDlik
Regarding the PCIE riser cable, I’m completely unsure what it is. Could you help me figure out how to check and force it?
Thank you!
M
Muezzze
08-03-2021, 11:45 PM #13

Here are the 3 screenshots provided.
Check them out: https://imgur.com/a/p3mDlik
View: https://imgur.com/a/p3mDlik
Regarding the PCIE riser cable, I’m completely unsure what it is. Could you help me figure out how to check and force it?
Thank you!

N
nissan8
Junior Member
14
08-04-2021, 09:55 AM
#14
Consider raising the DDR voltage to 1.35V.
PCIE riser cable is needed for mounting graphics cards vertically. If you're unsure about this, it's likely you don't have it.
The PCIE slot can be set to BIOS 3.0 mode, which may enhance system stability.
N
nissan8
08-04-2021, 09:55 AM #14

Consider raising the DDR voltage to 1.35V.
PCIE riser cable is needed for mounting graphics cards vertically. If you're unsure about this, it's likely you don't have it.
The PCIE slot can be set to BIOS 3.0 mode, which may enhance system stability.

C
Cutie_Kitcat
Senior Member
644
08-04-2021, 10:55 AM
#15
Thank you for your feedback. I followed your advice to adjust the DDR voltage to 1.35, but when checking with CPU-Z, the values remain unchanged. I’m unsure if I made a mistake or if there’s another factor at play. Here’s the link to the photo and screenshots: https://imgur.com/a/Co6FlYT View: https://imgur.com/a/Co6FlYT
C
Cutie_Kitcat
08-04-2021, 10:55 AM #15

Thank you for your feedback. I followed your advice to adjust the DDR voltage to 1.35, but when checking with CPU-Z, the values remain unchanged. I’m unsure if I made a mistake or if there’s another factor at play. Here’s the link to the photo and screenshots: https://imgur.com/a/Co6FlYT View: https://imgur.com/a/Co6FlYT

G
Genaric
Junior Member
4
08-04-2021, 03:37 PM
#16
The change was applied accurately.
CPU-Z does not display the current DDR voltage.
It only presents SPD and XMP data.
G
Genaric
08-04-2021, 03:37 PM #16

The change was applied accurately.
CPU-Z does not display the current DDR voltage.
It only presents SPD and XMP data.

1
10010Sofie
Junior Member
20
08-06-2021, 03:07 PM
#17
Thank you for your feedback. I believe the solution lies in increasing the DDR voltage, as discussed. I've been eager to check if any freezing occurred after adjusting the voltage, and so far, none have appeared. I truly appreciate your support; I had been dealing with this problem for months due to the instability.

I'm curious about the standard voltage of my DDR (1.20 v) and why it might be causing issues. Isn't a lower voltage more reliable than a higher one? Also, why didn't this problem arise from the beginning? It started around six months ago, but before that (when I built the PC about two years ago), there were no such concerns.
1
10010Sofie
08-06-2021, 03:07 PM #17

Thank you for your feedback. I believe the solution lies in increasing the DDR voltage, as discussed. I've been eager to check if any freezing occurred after adjusting the voltage, and so far, none have appeared. I truly appreciate your support; I had been dealing with this problem for months due to the instability.

I'm curious about the standard voltage of my DDR (1.20 v) and why it might be causing issues. Isn't a lower voltage more reliable than a higher one? Also, why didn't this problem arise from the beginning? It started around six months ago, but before that (when I built the PC about two years ago), there were no such concerns.

A
awesome_socks
Junior Member
24
08-19-2021, 11:02 AM
#18
1.2V is the typical DDR4 voltage.
1.35V is the common OC voltage for DDR4.
XMP generally needs a higher voltage for DDR4.
It's unclear why the XMP profile on your cards didn't set a higher voltage automatically.
A
awesome_socks
08-19-2021, 11:02 AM #18

1.2V is the typical DDR4 voltage.
1.35V is the common OC voltage for DDR4.
XMP generally needs a higher voltage for DDR4.
It's unclear why the XMP profile on your cards didn't set a higher voltage automatically.

C
Caribbean_Blue
Senior Member
609
08-24-2021, 04:05 PM
#19
My motherboard doesn't have the option XMP in bios, so as I searched there is "AI Overclock Tuner" for AMD which compares to XMP in Intel boards.
It was set on "Auto" and there is an option called "D.O.C.P" , maybe I should have enabled "DOCP" instead of leaving it "Auto" ?
C
Caribbean_Blue
08-24-2021, 04:05 PM #19

My motherboard doesn't have the option XMP in bios, so as I searched there is "AI Overclock Tuner" for AMD which compares to XMP in Intel boards.
It was set on "Auto" and there is an option called "D.O.C.P" , maybe I should have enabled "DOCP" instead of leaving it "Auto" ?

J
Julie_08
Member
176
08-24-2021, 09:07 PM
#20
DOP or A-XMP - is XMP compatible with AMD systems.
As it has been functioning stably now, you shouldn't make any changes.
If you enable DOCP, the DDR voltage will likely revert to 1.2V.
J
Julie_08
08-24-2021, 09:07 PM #20

DOP or A-XMP - is XMP compatible with AMD systems.
As it has been functioning stably now, you shouldn't make any changes.
If you enable DOCP, the DDR voltage will likely revert to 1.2V.

Pages (3): Previous 1 2 3 Next