F5F Stay Refreshed Power Users Overclocking water cooling formula ix with thermaltake rgb

water cooling formula ix with thermaltake rgb

water cooling formula ix with thermaltake rgb

P
PPS
Junior Member
Find
4
04-26-2017, 11:28 AM
#1
Hello Overclkers,
This is my initial encounter with water cooling. I own the W4 RGB water block, a PR22 cylinder equipped with a water pump, (2) Riing12 fans, and an RL240 radiator for my Formula IX motherboard. I plan to overclock this system using the i7 7700k and 4133 memory. Due to my case design, I’ve positioned the pump on its side since that’s the only feasible way to fit it with my Mandingo Graphix card. I’m hoping it can still function properly even if it doesn’t. I’ll handle that connection later.

My main concern is avoiding leaks. I assume the small opening at the top leading into a narrow tube in the cylinder is meant for filling the pump. Once the pump is full, I need to prevent any leaks. I bought Permatex to assist with this. Should I apply the sealant just beneath the horizontal surface of the cap where it meets the cylinder head, or also on the threads to stop leaks? The same applies to the 1/4 inch fittings as well. Would it be safe to apply the sealant directly onto the threads to prevent leaks in my video card or motherboard? Also, is it okay if some of the sealant comes into contact with the O-ring? It’s designed to seal, so I’m confident I made the right choice.

Regarding the motherboard, it has four RGB headers—two for the armor lighting. I placed the W4 RGB water block in the third one because I didn’t want to use the included control box. I’m curious if I could connect two daisy-chained LED strings with a Y adapter to the fourth header, which holds the two 12 fans. The fans are 1500 RPM max and measure 120x120 mm. Even though I’m new to RGB and water cooling, I’m confident in my abilities. Any advice or suggestions would be greatly appreciated. I’m eager to contribute to this community.

Thanks in advance,
Daddy
Reply
Reply
P
PPS
04-26-2017, 11:28 AM #1

Hello Overclkers,
This is my initial encounter with water cooling. I own the W4 RGB water block, a PR22 cylinder equipped with a water pump, (2) Riing12 fans, and an RL240 radiator for my Formula IX motherboard. I plan to overclock this system using the i7 7700k and 4133 memory. Due to my case design, I’ve positioned the pump on its side since that’s the only feasible way to fit it with my Mandingo Graphix card. I’m hoping it can still function properly even if it doesn’t. I’ll handle that connection later.

My main concern is avoiding leaks. I assume the small opening at the top leading into a narrow tube in the cylinder is meant for filling the pump. Once the pump is full, I need to prevent any leaks. I bought Permatex to assist with this. Should I apply the sealant just beneath the horizontal surface of the cap where it meets the cylinder head, or also on the threads to stop leaks? The same applies to the 1/4 inch fittings as well. Would it be safe to apply the sealant directly onto the threads to prevent leaks in my video card or motherboard? Also, is it okay if some of the sealant comes into contact with the O-ring? It’s designed to seal, so I’m confident I made the right choice.

Regarding the motherboard, it has four RGB headers—two for the armor lighting. I placed the W4 RGB water block in the third one because I didn’t want to use the included control box. I’m curious if I could connect two daisy-chained LED strings with a Y adapter to the fourth header, which holds the two 12 fans. The fans are 1500 RPM max and measure 120x120 mm. Even though I’m new to RGB and water cooling, I’m confident in my abilities. Any advice or suggestions would be greatly appreciated. I’m eager to contribute to this community.

Thanks in advance,
Daddy

Reply
Reply
F
fish1029
Member
Find
56
04-26-2017, 06:09 PM
#2
the sealing is carried out using o-rings. they are placed on each part, fitting, cap, etc. you must avoid using products like Pematex. if the system is assembled properly, there will be no leaks. for accurate installation, it is recommended to study several guides to grasp the details.
Reply
Reply
F
fish1029
04-26-2017, 06:09 PM #2

the sealing is carried out using o-rings. they are placed on each part, fitting, cap, etc. you must avoid using products like Pematex. if the system is assembled properly, there will be no leaks. for accurate installation, it is recommended to study several guides to grasp the details.

Reply
Reply