F5F Stay Refreshed Hardware Desktop This Wi-Fi profile for ProArt X670E-CREATOR isn't functioning properly.

This Wi-Fi profile for ProArt X670E-CREATOR isn't functioning properly.

This Wi-Fi profile for ProArt X670E-CREATOR isn't functioning properly.

R
robbierobot99
Member
102
06-01-2022, 03:48 AM
#1
I recently assembled my ideal computer, but the main problem is XMP only affecting AI overclocking. Don’t worry about this link, lol. Asus ProArt X670E-CREATOR WIFI Performance Results - UserBenchmark ProArt X670E-CREATOR WIFI｜Motherboards｜ASUS USA. What I did: upgraded the BIOS to the newest release. Tested lowering RAM from 6000 to 4500, which triggers an orange light on startup, turns red, and shows an error about a DRAM issue related to XMP profile. Any suggestions would be really appreciated.
R
robbierobot99
06-01-2022, 03:48 AM #1

I recently assembled my ideal computer, but the main problem is XMP only affecting AI overclocking. Don’t worry about this link, lol. Asus ProArt X670E-CREATOR WIFI Performance Results - UserBenchmark ProArt X670E-CREATOR WIFI｜Motherboards｜ASUS USA. What I did: upgraded the BIOS to the newest release. Tested lowering RAM from 6000 to 4500, which triggers an orange light on startup, turns red, and shows an error about a DRAM issue related to XMP profile. Any suggestions would be really appreciated.

V
Viizion_PvPz
Senior Member
670
06-01-2022, 09:54 AM
#2
Which RAM are you attempting to utilize? Edit: I'm a bit confused.
V
Viizion_PvPz
06-01-2022, 09:54 AM #2

Which RAM are you attempting to utilize? Edit: I'm a bit confused.

M
Mundojogador
Member
67
06-02-2022, 07:59 PM
#3
From what I recall, the most recent BIOS updates for ASUS boards offer limited memory support, which may prevent successful use. You may need to try different approaches, though results are uncertain and you might have to wait for further BIOS releases before trying again. The main suggestion is attempting XMP without enabling it, setting the memory frequency to 5200 initially, adjusting timings (tCL, tRCD, tRP, tRAS, tRC) in the specified sequence, configuring DRAM voltage levels (VDD, VDDQ, VDDIO) to 1.4V, and setting VSOC to 1.25V. If the feature activates, proceed with gradual frequency increases until stable performance is achieved. Run a stress test afterward to confirm stability. Note: Using 128GB RAM could cause issues; upgrading to DDR5 4000 or higher is likely necessary. Edited May 24, 2023 by RONOTHAN##
M
Mundojogador
06-02-2022, 07:59 PM #3

From what I recall, the most recent BIOS updates for ASUS boards offer limited memory support, which may prevent successful use. You may need to try different approaches, though results are uncertain and you might have to wait for further BIOS releases before trying again. The main suggestion is attempting XMP without enabling it, setting the memory frequency to 5200 initially, adjusting timings (tCL, tRCD, tRP, tRAS, tRC) in the specified sequence, configuring DRAM voltage levels (VDD, VDDQ, VDDIO) to 1.4V, and setting VSOC to 1.25V. If the feature activates, proceed with gradual frequency increases until stable performance is achieved. Run a stress test afterward to confirm stability. Note: Using 128GB RAM could cause issues; upgrading to DDR5 4000 or higher is likely necessary. Edited May 24, 2023 by RONOTHAN##

E
EilaMummo
Member
116
06-05-2022, 12:23 AM
#4
Consider what Ronothan mentioned. It seems you're using four sticks as well. Some folks have raised concerns about DDR5 with four sticks, so you might want to try XMP with just two sticks instead.
E
EilaMummo
06-05-2022, 12:23 AM #4

Consider what Ronothan mentioned. It seems you're using four sticks as well. Some folks have raised concerns about DDR5 with four sticks, so you might want to try XMP with just two sticks instead.

B
BlueCreeper823
Junior Member
8
06-08-2022, 02:32 PM
#5
The F5-6000J3040G324 2x32 GB kits aren't listed in the memory QVL, which means there are no assurances for XMP functionality, especially when using two units. You might want to disable the two dimms on the secondary board since new boards are very strict about XMP with DDR5. This could increase your chances of success; I haven’t seen a 4x32 GB kit that works with any DDR5 board yet. Some mainboards don’t have any kits listed at all, so you’d be limited to those options.
B
BlueCreeper823
06-08-2022, 02:32 PM #5

The F5-6000J3040G324 2x32 GB kits aren't listed in the memory QVL, which means there are no assurances for XMP functionality, especially when using two units. You might want to disable the two dimms on the secondary board since new boards are very strict about XMP with DDR5. This could increase your chances of success; I haven’t seen a 4x32 GB kit that works with any DDR5 board yet. Some mainboards don’t have any kits listed at all, so you’d be limited to those options.

F
Fingleberry
Junior Member
33
06-09-2022, 05:42 AM
#6
Thanks! I'll take care of it right away!
F
Fingleberry
06-09-2022, 05:42 AM #6

Thanks! I'll take care of it right away!

F
FearMeSlaves
Junior Member
46
06-09-2022, 08:14 PM
#7
I'll give it a shot too! Thanks.
F
FearMeSlaves
06-09-2022, 08:14 PM #7

I'll give it a shot too! Thanks.

S
SmileyFishMC
Member
60
06-10-2022, 01:22 AM
#8
I executed the memory verification tool. Results show:
Module 0: Unknown, 32768 MB, 64-bit, 4800 MHz DIMM 0 P0 CHANNEL A G Skill Intl F5-6000J3040G32G
Module 1: Unknown, 32768 MB, 64-bit, 4800 MHz DIMM 1 P0 CHANNEL A G Skill Intl F5-6000J3040G32G
Module 2: Unknown, 32768 MB, 64-bit, 4800 MHz DIMM 0 P0 CHANNEL B G Skill Intl F5-6000J3040G32G
The output seems unusual, that's why it feels odd.
S
SmileyFishMC
06-10-2022, 01:22 AM #8

I executed the memory verification tool. Results show:
Module 0: Unknown, 32768 MB, 64-bit, 4800 MHz DIMM 0 P0 CHANNEL A G Skill Intl F5-6000J3040G32G
Module 1: Unknown, 32768 MB, 64-bit, 4800 MHz DIMM 1 P0 CHANNEL A G Skill Intl F5-6000J3040G32G
Module 2: Unknown, 32768 MB, 64-bit, 4800 MHz DIMM 0 P0 CHANNEL B G Skill Intl F5-6000J3040G32G
The output seems unusual, that's why it feels odd.

D
DanZabr
Member
69
06-11-2022, 04:26 PM
#9
I'm using a memory checker that displays the maximum JEDEC frequency supported by the DIMMs, not the current operating frequency.
D
DanZabr
06-11-2022, 04:26 PM #9

I'm using a memory checker that displays the maximum JEDEC frequency supported by the DIMMs, not the current operating frequency.

T
TNTMSTR
Junior Member
6
07-01-2022, 08:24 PM
#10
You understand running it at 64 gigabytes is acceptable. I'll just send back the remaining drives. It performed well with the 6,000 Asus ProArt X670E-CREATOR WIFI results—thanks for your support!
T
TNTMSTR
07-01-2022, 08:24 PM #10

You understand running it at 64 gigabytes is acceptable. I'll just send back the remaining drives. It performed well with the 6,000 Asus ProArt X670E-CREATOR WIFI results—thanks for your support!