F5F Stay Refreshed Hardware Desktop The power supply is making noises and flashing lights when you switch it on.

The power supply is making noises and flashing lights when you switch it on.

The power supply is making noises and flashing lights when you switch it on.

Pages (2): 1 2 Next
L
Linouka
Junior Member
9
11-25-2020, 01:01 PM
#1
I just upgraded my GPU from a RTX 3070 super FE (6x8 pin) to a 6900 XT (3x8 pin). That meant I had to replace my PSU. I switched from a Corsair CX750M to an MSI A750GF. After changing the PSU and GPU, I turned it on and it started making a clicking sound. The lights also flickered. I took everything apart and rebuilt the PC, but it still makes that noise. I tried a trick with a paperclip in the 4 and 5 slot on the 24-pin connector—it worked perfectly. I’m not sure what else to do except ask you all here for help. I’m really stuck. Thank you very much.
L
Linouka
11-25-2020, 01:01 PM #1

I just upgraded my GPU from a RTX 3070 super FE (6x8 pin) to a 6900 XT (3x8 pin). That meant I had to replace my PSU. I switched from a Corsair CX750M to an MSI A750GF. After changing the PSU and GPU, I turned it on and it started making a clicking sound. The lights also flickered. I took everything apart and rebuilt the PC, but it still makes that noise. I tried a trick with a paperclip in the 4 and 5 slot on the 24-pin connector—it worked perfectly. I’m not sure what else to do except ask you all here for help. I’m really stuck. Thank you very much.

A
arun280800
Junior Member
12
11-30-2020, 10:46 AM
#2
The process changes with the PSU; ensure you connect all cables from the MSI and avoid using Corsair ones unless necessary. Always stick to original cables when possible.
A
arun280800
11-30-2020, 10:46 AM #2

The process changes with the PSU; ensure you connect all cables from the MSI and avoid using Corsair ones unless necessary. Always stick to original cables when possible.

R
ricby
Senior Member
681
12-01-2020, 10:31 PM
#3
I used the previous power supply and it failed to start. I was just enjoying Minecraft when I looked into everything, and it worked fine then. I tried the paperclip method with the Corsair PSU again, and it powered on successfully. After that, I changed all the connections to MSI.
R
ricby
12-01-2020, 10:31 PM #3

I used the previous power supply and it failed to start. I was just enjoying Minecraft when I looked into everything, and it worked fine then. I tried the paperclip method with the Corsair PSU again, and it powered on successfully. After that, I changed all the connections to MSI.

A
57
12-02-2020, 05:39 AM
#4
Use the original cables for each power supply unit. They are designed specifically for the PSUs and cannot be swapped. Incorrect cables could damage any part of the system. When testing with a different PSU, update the cables as well. Avoid mixing different cables. Regarding recommendations, an 850-watt PSU is suggested for your graphics card, though it may not fully activate in idle mode.
A
archangeldream
12-02-2020, 05:39 AM #4

Use the original cables for each power supply unit. They are designed specifically for the PSUs and cannot be swapped. Incorrect cables could damage any part of the system. When testing with a different PSU, update the cables as well. Avoid mixing different cables. Regarding recommendations, an 850-watt PSU is suggested for your graphics card, though it may not fully activate in idle mode.

T
Tehtz
Junior Member
24
12-02-2020, 07:36 AM
#5
Can you check for signs of frying? There’s a simple way to test it.
T
Tehtz
12-02-2020, 07:36 AM #5

Can you check for signs of frying? There’s a simple way to test it.

X
xeal987
Member
59
12-04-2020, 06:39 AM
#6
Avoid this route—verify each part separately within a different setup. This is the most challenging situation. Consider fitting your previous PSU using the original connectors and testing your old GPU to check for booting capability.
X
xeal987
12-04-2020, 06:39 AM #6

Avoid this route—verify each part separately within a different setup. This is the most challenging situation. Consider fitting your previous PSU using the original connectors and testing your old GPU to check for booting capability.

K
Kassara
Member
55
12-18-2020, 10:39 PM
#7
You recently checked your old motherboard MSI Gaming Edge i3-9100F using the latest MSI power supply, but the clicking sound persisted.
K
Kassara
12-18-2020, 10:39 PM #7

You recently checked your old motherboard MSI Gaming Edge i3-9100F using the latest MSI power supply, but the clicking sound persisted.

W
W_O_L_F_R_A_M
Member
125
12-25-2020, 06:35 AM
#8
It seems the PSU is likely damaged. This component often triggers a shutdown once the CPU powers down. It might have activated some protection feature. For the 6900, aim for a minimum of 850 watts as shown on the MSI site.
W
W_O_L_F_R_A_M
12-25-2020, 06:35 AM #8

It seems the PSU is likely damaged. This component often triggers a shutdown once the CPU powers down. It might have activated some protection feature. For the 6900, aim for a minimum of 850 watts as shown on the MSI site.

S
SuperRxns
Member
102
12-25-2020, 09:07 AM
#9
Your PGU isn't linked yet, and it seems to be having issues even when using the paperclip.
S
SuperRxns
12-25-2020, 09:07 AM #9

Your PGU isn't linked yet, and it seems to be having issues even when using the paperclip.

_
_Aahrix_
Junior Member
12
12-25-2020, 12:22 PM
#10
Removing the GPU from the PCIe slot affects things further. Disconnecting unused components like extra storage or fans can help. Try using only essential items for post-processing; if it works but the screen stays black, there might be an issue. It looks like a short is likely occurring somewhere.
_
_Aahrix_
12-25-2020, 12:22 PM #10

Removing the GPU from the PCIe slot affects things further. Disconnecting unused components like extra storage or fans can help. Try using only essential items for post-processing; if it works but the screen stays black, there might be an issue. It looks like a short is likely occurring somewhere.

Pages (2): 1 2 Next