F5F Stay Refreshed Hardware Desktop The PC powers up yet there is no visible output.

The PC powers up yet there is no visible output.

The PC powers up yet there is no visible output.

Y
YoYo7
Member
75
03-18-2021, 08:51 PM
#1
Hey so I have replaced my Arctic Freezer 2 AIO via rma for a new one . Did it and installed it but now my PC does turn on. The pump works as I can see and hear it pumping water and the PC fans spin but my display lights up for a sec then turns off and when I manually turn it on it can not find a signal source. When I press the "Change Source" button. ( I use DisplayPort ) it switches to different ones but can not find anything and then a message pops up that I should check the cable or the output device .
BUT when I plug my monitor into my old pc it works . So I have:
Reset the bios by removing the battery.
Pulled out the ram and inserted 1 stick instead of 4 - nothing .
Taken out the 3060 Ti and connected the monitor to the mobo - nothing .
Installed my 1070 in th PC - nothing .
Unplugged the aio and booted it and still the same turns on but no display output .
Tried it out with 2 different monitors and the same happens all the time .
Any idea which component can be causing this and how to fix it ?
No idea if this is important or not but my PC was unplugged from power for a week while waiting for the new AIO .
My components
i9-10900
3060 ti gigabyte
3600 ram 4x kingston fury
750 watt psu
2X ssd 2x hdd
Asus z 590 mobo
2x samsung monitors
Arctic liquid freezer 2
Y
YoYo7
03-18-2021, 08:51 PM #1

Hey so I have replaced my Arctic Freezer 2 AIO via rma for a new one . Did it and installed it but now my PC does turn on. The pump works as I can see and hear it pumping water and the PC fans spin but my display lights up for a sec then turns off and when I manually turn it on it can not find a signal source. When I press the "Change Source" button. ( I use DisplayPort ) it switches to different ones but can not find anything and then a message pops up that I should check the cable or the output device .
BUT when I plug my monitor into my old pc it works . So I have:
Reset the bios by removing the battery.
Pulled out the ram and inserted 1 stick instead of 4 - nothing .
Taken out the 3060 Ti and connected the monitor to the mobo - nothing .
Installed my 1070 in th PC - nothing .
Unplugged the aio and booted it and still the same turns on but no display output .
Tried it out with 2 different monitors and the same happens all the time .
Any idea which component can be causing this and how to fix it ?
No idea if this is important or not but my PC was unplugged from power for a week while waiting for the new AIO .
My components
i9-10900
3060 ti gigabyte
3600 ram 4x kingston fury
750 watt psu
2X ssd 2x hdd
Asus z 590 mobo
2x samsung monitors
Arctic liquid freezer 2

N
Nayumo
Member
118
03-18-2021, 11:46 PM
#2
Ensure the cooling plate isn't too tight against the CPU. This might be causing the issue. You might also want to take out the CMOS battery and attempt to restart the PC.
N
Nayumo
03-18-2021, 11:46 PM #2

Ensure the cooling plate isn't too tight against the CPU. This might be causing the issue. You might also want to take out the CMOS battery and attempt to restart the PC.

T
tim_ki
Member
196
03-19-2021, 06:38 AM
#3
It is very tight with a quarter turn extra for most chips.
T
tim_ki
03-19-2021, 06:38 AM #3

It is very tight with a quarter turn extra for most chips.