F5F Stay Refreshed Hardware Desktop Temperatures and clock speeds for the Ryzen 5 3600.

Temperatures and clock speeds for the Ryzen 5 3600.

Temperatures and clock speeds for the Ryzen 5 3600.

Pages (2): 1 2 Next
W
WD_Trashster
Senior Member
454
10-23-2019, 08:16 PM
#1
Hi everyone! I've been having some kind of weird stuff going on with my cpu. First of all, specs: Ryzen 5 3600 Asus Prime X570-Pro Hyperx 2x8 at 3200Mhz As a cooler I'm using my old CoolerMaster ML120R RGB. With custom fans Only software being run for RGB control: Armoury Crate. Software for checking temps, voltages and frequencies: Ryzen Master CPU-Z I have POB and DOCP disabled.. (Should I enable them?) So, by default it runs between 35 - 45°C (Ryzen balanced power plan). It reaches 60-65 while gaming Now, the problems: I've not been able to make it go higher than 4.0 ghz. Voltages at 1.35-1.4 Sometimes Armoury Crate decides to reset or something, and I've to configure all my RGB again. Once while doing this I noticed quite unusual temps. Testing a bit I found out that, and here's the weird part, if I don't set a color/effect/whatever my temps go up by 10°C. Always, no exception. And it's always by 10°C Has anyone ever encountered something like this? I'm actually worried about the rgb stuff, the other one is quite common from what I read until now. Before anyone asks, all my drivers, bios, chipset, whatever is updated.
W
WD_Trashster
10-23-2019, 08:16 PM #1

Hi everyone! I've been having some kind of weird stuff going on with my cpu. First of all, specs: Ryzen 5 3600 Asus Prime X570-Pro Hyperx 2x8 at 3200Mhz As a cooler I'm using my old CoolerMaster ML120R RGB. With custom fans Only software being run for RGB control: Armoury Crate. Software for checking temps, voltages and frequencies: Ryzen Master CPU-Z I have POB and DOCP disabled.. (Should I enable them?) So, by default it runs between 35 - 45°C (Ryzen balanced power plan). It reaches 60-65 while gaming Now, the problems: I've not been able to make it go higher than 4.0 ghz. Voltages at 1.35-1.4 Sometimes Armoury Crate decides to reset or something, and I've to configure all my RGB again. Once while doing this I noticed quite unusual temps. Testing a bit I found out that, and here's the weird part, if I don't set a color/effect/whatever my temps go up by 10°C. Always, no exception. And it's always by 10°C Has anyone ever encountered something like this? I'm actually worried about the rgb stuff, the other one is quite common from what I read until now. Before anyone asks, all my drivers, bios, chipset, whatever is updated.

F
FromTheJakob
Junior Member
2
10-28-2019, 05:49 PM
#2
It doesn't make sense to expect a CPU to run at a specific clock speed after purchasing it—perhaps the component is defective.
F
FromTheJakob
10-28-2019, 05:49 PM #2

It doesn't make sense to expect a CPU to run at a specific clock speed after purchasing it—perhaps the component is defective.

D
Der_Zwieback
Member
148
10-30-2019, 12:00 AM
#3
The cooler is 5 years old.
D
Der_Zwieback
10-30-2019, 12:00 AM #3

The cooler is 5 years old.

M
mitchymoo04
Junior Member
15
10-30-2019, 12:12 AM
#4
DCP must be activated. It might feel a bit weak, but it’s not impossible to reach higher. Using only PBO provides what?
M
mitchymoo04
10-30-2019, 12:12 AM #4

DCP must be activated. It might feel a bit weak, but it’s not impossible to reach higher. Using only PBO provides what?

G
gavcanz32
Member
140
10-30-2019, 03:38 AM
#5
Approximately 4 to 5 months later. I don’t have to worry about the temperatures; according to what I’ve learned, this chip tends to get quite hot. What concerns me is that adjusting my RGB settings raises my CPU temperature by about 10 degrees. Making that change actually reduces it by 10°C.
G
gavcanz32
10-30-2019, 03:38 AM #5

Approximately 4 to 5 months later. I don’t have to worry about the temperatures; according to what I’ve learned, this chip tends to get quite hot. What concerns me is that adjusting my RGB settings raises my CPU temperature by about 10 degrees. Making that change actually reduces it by 10°C.

F
FureaMC
Senior Member
564
10-31-2019, 03:53 PM
#6
I'll turn it on right away—I believe PBO is already off. I'll activate it and let you know what I see. What are your thoughts on the RGB aspect?
F
FureaMC
10-31-2019, 03:53 PM #6

I'll turn it on right away—I believe PBO is already off. I'll activate it and let you know what I see. What are your thoughts on the RGB aspect?

F
FionnMacu
Member
147
11-02-2019, 06:11 AM
#7
I strongly prefer not to use RGB and I’m new to lighting software.
F
FionnMacu
11-02-2019, 06:11 AM #7

I strongly prefer not to use RGB and I’m new to lighting software.

W
willguMC
Member
74
11-02-2019, 07:51 AM
#8
Looks genuine. I’ve been thinking about moving away from the RGB space. All the problems, lots of bugs, and high costs are discouraging. Appreciate the support—will turn on DOCP and PBO and share the outcomes.
W
willguMC
11-02-2019, 07:51 AM #8

Looks genuine. I’ve been thinking about moving away from the RGB space. All the problems, lots of bugs, and high costs are discouraging. Appreciate the support—will turn on DOCP and PBO and share the outcomes.

Z
Zeus707xd
Junior Member
13
11-06-2019, 08:19 PM
#9
Absolutely, the problems are clear. I suggest checking out this discussion—it's quite informative.
Z
Zeus707xd
11-06-2019, 08:19 PM #9

Absolutely, the problems are clear. I suggest checking out this discussion—it's quite informative.

N
NicoPlaysYT
Senior Member
250
11-08-2019, 05:43 AM
#10
I'm sorry, I don't understand what you're saying. Could you please clarify your question?
N
NicoPlaysYT
11-08-2019, 05:43 AM #10

I'm sorry, I don't understand what you're saying. Could you please clarify your question?

Pages (2): 1 2 Next