System failure detected. Please restart your PC to resolve the issue.
System failure detected. Please restart your PC to resolve the issue.
Hi, I understand you're seeking assistance with a recent issue. While testing on your PC, it shut down unexpectedly. There were no loud noises or interruptions. I assumed a power outage might be the cause. When you turned it back on, the RGB lights came on but the system seemed to keep cycling, failing to fully power up. The motherboard features EZ Debug LEDs that display similar cycles for CPU, VGA, and Boot. I replaced the GPU with an older GTX1070 to check if that was the problem. The same LED pattern appeared, but the monitor showed a flashing screen before restarting. I'm looking for guidance on possible causes and troubleshooting steps, especially since I have spare parts from my previous setup. Any advice would be greatly appreciated, Brian. Thanks!
Disable CMOS fully, leaving only essential devices connected. Use just one RAM stick and test in each slot, swapping it with others. Switch the power supply if needed.
I restored the CMOS, restarted from post and confirmed everything was fine without major adjustments. Setup entered BIOS, everything appeared normal. Disconnected all drives except one, which was listed as NVMe. It reset CMOS again and BIOS worked properly. I verified it showed no issues, closed BIOS, and it booted back. It seems the NVMe wasn’t the first bootable device, so it just loops. Next, I want to check the power supply unit—can it fail silently without providing enough power? Thanks for your assistance. I really prefer not to disassemble it.
I ran a self-test on my SSD using BIOS and everything looked normal. But maybe the data is damaged instead of the drive itself being faulty. I’ll try booting with a Windows 10 USB to check. I’m planning to review the results tomorrow. I’ll update you then.
Ensure your boot drive is correctly chosen. I experienced this issue with my laptop where it repeatedly restarted due to an unexpected switch from drive C to D, making it impossible to launch Windows. Also, could you tell me how far along the boot sequence you are? Have you attempted entering safe mode?
Even reaching this point isn't much. Appreciate it. I'll verify the bios for boot choices next time.
Hello, @Hairless Monkey Boy Right after removing the mobo and everything from the case i thought i would check what happened if i tried booting without the nvme drive in.... why i didnt try this before i honestly have no correct answer, ask for help and only follow part of the suggestions.... well human nature i suppose. So no drive in went to bios. Put a blank ssd hdd in and it told me to select a correct bootable drive. So looks like it was the drive that is broken. Now some other questions, i have files on c that i dont have anywhere else (i know they should have been backed up). Is there a chance once i have it booting again ill be access the drive in windows? After that is done will i be able to just format the drive and install windows back on it? I know its hard to answer these questions, but your opinons will help me out. Ill be able to just fit it all together now install windows on a 250gb drive then try and salvage whats on the drive then reformat it. Or buy a new drive. Thanks again for all your help in this matter. Brian.
This might stem from the initial installation method of Windows. Consider comparing UEFI with Legacy settings, especially regarding CSM configurations. Resetting the BIOS to its default optimized state could help. Ensure you boot from the Windows installation media in UEFI mode if the issue persists. Collecting necessary data from the drive is also crucial—verify that your NVME device appears correctly when Windows is installed on the 250GB disk and successfully retrieves your files. If you encounter permission or data retrieval challenges, let me know. The recommended approach involves installing Windows on a single drive, booting in UEFI mode via the Windows USB, opting for a custom installation, clearing existing partitions, and selecting unallocated space for setup. After installation, safely shut down and reconnect other drives.
The issue seems to be with the installation process not starting properly. I created a fresh USB installer using Win 10 Media Creator but it kept looping back into the boot menu. After some research, I found Rufus and tried making another installer from that tool, yet it didn’t work. I’ve tested different USB ports, but I’m still unsure what to do next. I’m attempting to install it onto a standard SATA SSD, as indicated in the BIOS settings. If you don’t have any bootable media available, I can access the BIOS directly. Thanks for your assistance. Brian.