Struggling to recognize and resolve this outdated motherboard, require assistance

S

S4NP3I
Member

194

02-28-2016, 05:36 AM

#1

I found this vintage motherboard in an older setup and attempted to start it up. The 160GB WD Blue IDE drive ran Windows XP, but it consistently froze at the loading bar. The VGA output seemed distorted. When I booted XP from a CD, I encountered an error stating that vga.sys was damaged. I suspected an issue with the motherboard's IGPU and installed an older AGP graphics card (Gigabyte Radeon 7000 64MB), which worked for the VGA signal but still caused the XP installation to fail with the same error. I experimented with advanced settings, safe mode, and sometimes the XP would crash or display a blue screen only visible via slow-motion footage. I managed to capture a frame of the issue. Please share photos of the board and the installation errors you experienced. Appreciate any guidance! For those curious, I understand the socket is MPEG-H and the CPU is a Celeron D @ 2.0GHz with 512MB DDR1 RAM. The IDE ports run at 133/33MHz, and I also tried a single RAM stick and a different CD drive. The included 56k CD drive didn’t help. If you know where to locate IGPU drivers or BIOS updates for this board, it would be helpful. Thanks again! Edited June 12, 2024 by bobby3dse Added GPU details

D

Drone_947
Member

60

02-28-2016, 01:05 PM

#2

Looking into this might have been a while ago. The Jetway brand hasn’t been mentioned much recently. Regarding vga.sys, it seems you haven’t seen it in a long time either—consider verifying your XP installation for any issues.

V

Valyrian_
Member

201

02-29-2016, 04:27 AM

#3

It looks like you're wondering about testing a website and verifying the XP install source. You haven’t tried it yet, so you can start there. To check for errors in the XP install source, look for any warnings or issues during the installation process.

M

MegaDisco
Senior Member

352

03-01-2016, 05:44 AM

#4

Your motherboard has numerous bad capacitors. (That's a very common problem with Socket 478 era boards.) It's never going to be stable if its power delivery is sketchy. Spoiler

O

oOEmmaOo
Posting Freak

818

03-02-2016, 07:47 PM

#5

Absolutely, you got it. Those capacitors are definitely bad. The VGA.sys issue points to a kernel driver problem in Windows XP—possibly a corrupted CD. I’m stuck on my end too; XP feels tricky for me. Also, the Retail vs OEM setup and Service Packs had some weird behavior back then.

S

sandieaak
Member

182

03-23-2016, 04:31 AM

#6

Another idea came to mind that might have been overlooked. Despite the numerous issues, it managed to start. I didn’t expect much effort since I wasn’t really aiming for it. Appreciate the details from both of you.

J

JokerFame
Senior Member

670

04-09-2016, 10:03 PM

#7

I understand you're asking about identifying faulty capacitors. Let's focus on the signs that might indicate a problem. Look for visible damage such as burn marks, discoloration, or physical deformation. Also check for unusual odors, leakage, or inconsistent performance in your circuit. If you notice these clues, it could help determine if the capacitors are indeed bad.

D

DrBrokenBones
Senior Member

378

04-10-2016, 12:04 AM

#8

the side next to the CPU is already leaking, and most of the others show their tops bulging or swelling before leaking. this design has grooves on top so they can open rather than burst.

K

KlimonLimon
Junior Member

3

04-10-2016, 01:26 AM

#9

Great! Let's get started.