Setting up the Cooler Master Hyper 212+
Setting up the Cooler Master Hyper 212+
How to set up your new cooler? A brief tutorial
Hello everyone, this is my initial guide, so please keep it simple.
Before you begin, here are some important tips.
A. First, ensure you purchase a cooler that fits your case perfectly. Doing so will prevent issues when closing the case later.
B. Verify that the cooler's socket matches your system's requirements—some models only support specific processors like i7 or AM3. Choosing the wrong one could waste your investment.
C. Check that your RAM capacity is appropriate; otherwise, it might cause problems with the socket proximity.
D. Lastly, eliminate any static electricity buildup to avoid damaging your motherboard, processor, or other components. If you don’t have an anti-static mat, touch the PC case or connect it to a metal surface before starting.
For a clearer visual reference, click on the attached image.
1. After preparing these steps, let’s move on to the installation process. I used a CoolerMaster Hyper 212+ in an MSI K9A2 Platinum with an AM2/AM2+ socket and a Phenom II X4 955. My case is a Thermaltake V9.
2. Disconnect all cables from your PC, including the keyboard, mouse, power supply, audio, and any other peripherals connected to your case.
P.D. I’m aware my system management cable isn’t ideal.
3. If your case lacks a tray for the motherboard, you’ll need to remove the motherboard itself to properly install the cooler. Don’t forget to detach the PSU, HD drives, GPU, and other components beforehand.
P.D. This step is crucial.
4. Once everything is ready, remove the old cooler and its support. If your case doesn’t have a tray, carefully pull out the motherboard to access it properly.
P.D. I believe this is necessary.
5. After that, use a thermal grease remover or a soft cloth to clean any residue from the processor. You can use a lint-free cloth to avoid leaving dust or paper.
6. Take off the current cooler support and its backing plate. The process involves removing screws on the front side of the motherboard.
7. Now that the old cooler is removed, you can install the new cooler support and complete the setup. Follow the instructions carefully for each step.
Please note the final instructions are clear and concise.
8. Following that, you should have tightened all the screws using the nuts on the back plate (back side of the mobo). After that, you must put the retention plate into the cooler. To do this, you need to adjust the screws according to your socket.
To fit the retention plate onto your socket, examine the screws in it, since the retention plate comes with screws by default for a mobo with socket 775. Here are some recommendations:
a. For socket 775, keep the screws unchanged
b. For socket AM2/AM2+/AM3 or 1156, adjust the screws to the second hole on the retention plate
c. For socket 1366, adjust the screws to the last hole on the retention plate.
9. Next, apply thermal grease to your new cooler, but first remove the protective layer from the bottom of the cooler. Don’t use all the grease that comes with it—just enough to cover the CPU. You can apply it to either the cooler or the CPU.
Update: Thanks to lutfij for sharing this helpful guide.
Thermal Paste Application
10. Once installed, you can place the cooler in your mobo. Make sure the screws align with the first screws you used at the start of the process. Adjust them in the X direction, not along the side.
Update: You have two options for installing the cooler—vertical or horizontal, depending on your preference, airflow, and case space. Thanks to JofaMang for the advice.
11. Next, attach the fan to the cooler. Simply connect the fan brackets to the fan (included by the manufacturer) and secure it to the cooler. Keep in mind this step is only necessary if you plan to install a second fan or if the fan isn’t included.
As you can see, there may be some challenges here. If your RAM size is large (such as from Kingston HyperX, G.Skill, or Corsair) and it’s very close to your processor, fitting the new cooler could be difficult. In that case, consider installing it in the opposite orientation—fan side up or down depending on your case design.
15. Once everything is set, you can put the mobo back into your case, reconnect all connections, and begin overclocking.
/-------------------------------------------------/
1- If you have any questions, feel free to ask here or in the forum—we’re here to assist.
2- If you’d like additional details, just let me know.
3- If you have suggestions or corrections, please share them.
Remember, English isn’t your native language, so don’t worry too much. Have fun!
Thx both, it's a Sony Cyber-shot DSC-S950, it's a basic model, but is very good.
Haha, which country are you from? I was also thinking about getting the EOS REBEL XTi.
Great resource. It will definitely assist beginners in setting up aftermarket coolers.