F5F Stay Refreshed Hardware Desktop Running at thermal limit after days of normal operation.

Running at thermal limit after days of normal operation.

Running at thermal limit after days of normal operation.

H
helenma0301
Senior Member
250
06-15-2022, 03:35 PM
#1
Hello! I'm facing a problem with my new PC setup. It's a Ryzen 7 9700x with an Arctic Liquid Freezer III 360 mounted at the top. This morning when I first tried to start it, the fans started spinning up, making me worry about the fan curve settings. I checked hwinfo and noticed some freezing issues. I powered off the machine by pressing the power button for a hard reset, then went into BIOS where I saw an idle temperature of 67°C before it shut down itself. Previously, everything ran smoothly with normal temperatures during both idle and full load, and I hadn't made any changes the day before. Next, I tried shorting the JBAT1 connection on my MSI MAG B650 Tomahawk motherboard to clear CMOS. The process showed a slight difference, allowing me to boot into Windows. The temperatures stayed between 80°C and 95°C across all cores, even though it was using only 25W power. I could re-seat the CPU or apply more thermal paste, but this seems unusual since it happened overnight. What steps should I take to troubleshoot further? Check PCPartPicker part list here: https://uk.pcpartpicker.com/list/pzyz6Q
H
helenma0301
06-15-2022, 03:35 PM #1

Hello! I'm facing a problem with my new PC setup. It's a Ryzen 7 9700x with an Arctic Liquid Freezer III 360 mounted at the top. This morning when I first tried to start it, the fans started spinning up, making me worry about the fan curve settings. I checked hwinfo and noticed some freezing issues. I powered off the machine by pressing the power button for a hard reset, then went into BIOS where I saw an idle temperature of 67°C before it shut down itself. Previously, everything ran smoothly with normal temperatures during both idle and full load, and I hadn't made any changes the day before. Next, I tried shorting the JBAT1 connection on my MSI MAG B650 Tomahawk motherboard to clear CMOS. The process showed a slight difference, allowing me to boot into Windows. The temperatures stayed between 80°C and 95°C across all cores, even though it was using only 25W power. I could re-seat the CPU or apply more thermal paste, but this seems unusual since it happened overnight. What steps should I take to troubleshoot further? Check PCPartPicker part list here: https://uk.pcpartpicker.com/list/pzyz6Q

S
Sparkle_Wolf
Junior Member
27
06-16-2022, 12:19 AM
#2
When the processor heats up, inspect both sections of the AIO tubes to check their temperature. If only one or none feel warm, the water circulation within the AIO isn't functioning properly.
S
Sparkle_Wolf
06-16-2022, 12:19 AM #2

When the processor heats up, inspect both sections of the AIO tubes to check their temperature. If only one or none feel warm, the water circulation within the AIO isn't functioning properly.

M
Marcustheduke
Senior Member
679
06-16-2022, 03:25 AM
#3
When activated, press the AIO tubes and notice the flow of water.
M
Marcustheduke
06-16-2022, 03:25 AM #3

When activated, press the AIO tubes and notice the flow of water.

A
Ac1dicBlitzz
Member
206
06-16-2022, 05:24 AM
#4
It seems water is flowing somewhere, and I detected some vibrations from the tubes. I plan to disconnect several fans to confirm it's due to high usage. Also observing some heat escaping from the top of the radiator.
A
Ac1dicBlitzz
06-16-2022, 05:24 AM #4

It seems water is flowing somewhere, and I detected some vibrations from the tubes. I plan to disconnect several fans to confirm it's due to high usage. Also observing some heat escaping from the top of the radiator.

M
moffy
Member
59
06-16-2022, 08:47 AM
#5
Is the pump spinning around 3000 rpm or higher? The lack of noticeable heat dissipation suggests either poor flow or an unstable mount.
M
moffy
06-16-2022, 08:47 AM #5

Is the pump spinning around 3000 rpm or higher? The lack of noticeable heat dissipation suggests either poor flow or an unstable mount.

D
Dave1304
Member
180
06-17-2022, 03:37 PM
#6
It seems the link wasn't working properly and the AIO wasn't running, so this issue needs to be addressed soon.
D
Dave1304
06-17-2022, 03:37 PM #6

It seems the link wasn't working properly and the AIO wasn't running, so this issue needs to be addressed soon.