Ram performance issues at full capacity

Pages (3): Previous 1 2 3 Next

FREEFLY12_YT
Junior Member

02-22-2019, 02:06 AM

#11

I reduced the voltage to 1.3 and it started up at 3600, we'll check for stability.

FREEFLY12_YT

02-22-2019, 02:06 AM #11

I reduced the voltage to 1.3 and it started up at 3600, we'll check for stability.

Kangmiester18
Member

115

02-22-2019, 08:32 AM

#12

The system starts up now, yet it immediately clears your computer after a short time.

Kangmiester18

02-22-2019, 08:32 AM #12

The system starts up now, yet it immediately clears your computer after a short time.

Bellabell11295
Member

154

02-22-2019, 02:07 PM

#13

Did you turn on the DOCP or XMP settings? Avoid handling the voltage. The RAM will work at 1.35V just fine. With the same setup (DocP on auto), my timings are 16-19-19-39 at 1.35V and 3603MHz.

Bellabell11295

02-22-2019, 02:07 PM #13

Did you turn on the DOCP or XMP settings? Avoid handling the voltage. The RAM will work at 1.35V just fine. With the same setup (DocP on auto), my timings are 16-19-19-39 at 1.35V and 3603MHz.

jack_maniss
Junior Member

02-25-2019, 11:47 AM

#14

I didn't find the document you're looking for.

jack_maniss

02-25-2019, 11:47 AM #14

I didn't find the document you're looking for.

Ungrame1
Member

02-25-2019, 12:45 PM

#15

There were XMP available.

Ungrame1

02-25-2019, 12:45 PM #15

There were XMP available.

XshalevX
Member

02-25-2019, 08:08 PM

#16

Just use 16-19-19-39 1.35V and 3600mhz. I can't do that.

XshalevX

02-25-2019, 08:08 PM #16

Just use 16-19-19-39 1.35V and 3600mhz. I can't do that.

Toodaloo_246
Senior Member

439

02-26-2019, 05:13 PM

#17

Yes enable that

Toodaloo_246

02-26-2019, 05:13 PM #17

Yes enable that

24_LuLu
Junior Member

03-06-2019, 02:40 PM

#18

I try, but once I attempt it I still can't share again.

24_LuLu

03-06-2019, 02:40 PM #18

I try, but once I attempt it I still can't share again.

bubalu529
Member

114

03-09-2019, 02:25 PM

#19

Set the XMP values first, then raise the voltage to 1.4. Use one probe at a time.

bubalu529

03-09-2019, 02:25 PM #19

Set the XMP values first, then raise the voltage to 1.4. Use one probe at a time.

MissNerdyGirl
Junior Member

03-09-2019, 10:51 PM

#20

Adjust the xmp settings manually—modify timing and RAM speed to match xmp specifications—while raising the voltage to 1.4.

MissNerdyGirl

03-09-2019, 10:51 PM #20

Adjust the xmp settings manually—modify timing and RAM speed to match xmp specifications—while raising the voltage to 1.4.

Pages (3): Previous 1 2 3 Next