F5F Stay Refreshed Hardware Desktop Processor rests at 50°C, runs games smoothly up to 100°C.

Processor rests at 50°C, runs games smoothly up to 100°C.

Processor rests at 50°C, runs games smoothly up to 100°C.

Pages (3): Previous 1 2 3 Next
B
baconandfries
Member
215
06-21-2023, 05:36 AM
#11
The pressure isn't strong enough for these Intel fan tabs
B
baconandfries
06-21-2023, 05:36 AM #11

The pressure isn't strong enough for these Intel fan tabs

T
Th3_K1ll3r
Junior Member
12
06-22-2023, 07:10 PM
#12
The device features connectors instead of fasteners.
T
Th3_K1ll3r
06-22-2023, 07:10 PM #12

The device features connectors instead of fasteners.

X
65
06-25-2023, 07:58 PM
#13
The connections can be challenging to verify they’re securely fastened. Sometimes they look locked but aren’t. They don’t feel intuitive for re-installing after the initial setup. The locking tabs must be closed before pushing them onto the board; once in place, the pin slides in and turns, but I still have trouble mounting it correctly.
X
xXSyntooxienXx
06-25-2023, 07:58 PM #13

The connections can be challenging to verify they’re securely fastened. Sometimes they look locked but aren’t. They don’t feel intuitive for re-installing after the initial setup. The locking tabs must be closed before pushing them onto the board; once in place, the pin slides in and turns, but I still have trouble mounting it correctly.

E
EisTeeKlaus
Senior Member
490
06-25-2023, 09:56 PM
#14
Mmm... yes, a horizontal motherboard helps somewhat, but not much. All metal-to-metal contacts must be secure. That’s why thermal paste is useful. It supports that bond. Thermal paste isn’t an excellent conductor, but it’s still better than air. There should be a guide on how to install a CPU cooler properly somewhere. Anyone have a link? The older 1150 models had frustrating plastic pins that often failed and were easy to damage. That 4790k is a tough CPU—it overclocks easily and gets hot. I thought about buying a used one recently. A stock fan from Intel on that unit would be a small mistake. I own a 4770k with a six-pipe cooler and diamond paste.
E
EisTeeKlaus
06-25-2023, 09:56 PM #14

Mmm... yes, a horizontal motherboard helps somewhat, but not much. All metal-to-metal contacts must be secure. That’s why thermal paste is useful. It supports that bond. Thermal paste isn’t an excellent conductor, but it’s still better than air. There should be a guide on how to install a CPU cooler properly somewhere. Anyone have a link? The older 1150 models had frustrating plastic pins that often failed and were easy to damage. That 4790k is a tough CPU—it overclocks easily and gets hot. I thought about buying a used one recently. A stock fan from Intel on that unit would be a small mistake. I own a 4770k with a six-pipe cooler and diamond paste.

R
Robotic_Slap
Member
134
06-26-2023, 10:53 AM
#15
It seems the IHS isn't soldered and the thermal paste is dry. A dry paste can block heat flow, so you may need to remove the CPU's heat paste.
R
Robotic_Slap
06-26-2023, 10:53 AM #15

It seems the IHS isn't soldered and the thermal paste is dry. A dry paste can block heat flow, so you may need to remove the CPU's heat paste.

S
smider3
Member
107
07-10-2023, 04:21 AM
#16
It wouldn’t be as good without a decent cooling solution. Swapping it out for a suitable cooler would really boost performance.
S
smider3
07-10-2023, 04:21 AM #16

It wouldn’t be as good without a decent cooling solution. Swapping it out for a suitable cooler would really boost performance.

A
AdamKoudy
Senior Member
740
07-10-2023, 05:19 AM
#17
The 5-year-old thermal paste isn’t transferring heat well enough. Using an old paste likely caused this issue. The high temperatures weren’t normal back then, so it probably isn’t the cooler. This CPU might need some cleaning or replacement.
A
AdamKoudy
07-10-2023, 05:19 AM #17

The 5-year-old thermal paste isn’t transferring heat well enough. Using an old paste likely caused this issue. The high temperatures weren’t normal back then, so it probably isn’t the cooler. This CPU might need some cleaning or replacement.

X
XxGrenidierXx
Posting Freak
813
07-10-2023, 08:19 AM
#18
I also re-applied thermal paste last night.
X
XxGrenidierXx
07-10-2023, 08:19 AM #18

I also re-applied thermal paste last night.

W
WildFlow
Member
187
07-12-2023, 03:13 AM
#19
There is also a thermal paste under the metal "plate" of the CPU, It was a d*ck move from Intel to put thermal paste there instead of soldering the metal "plate" to the CPU. Intel did it because thermal paste is cheaper than soldering. There are special tools that make delidding easier and safer,you don't want your to damage your CPU after all. Here is a video of Linus delidding a CPU:
W
WildFlow
07-12-2023, 03:13 AM #19

There is also a thermal paste under the metal "plate" of the CPU, It was a d*ck move from Intel to put thermal paste there instead of soldering the metal "plate" to the CPU. Intel did it because thermal paste is cheaper than soldering. There are special tools that make delidding easier and safer,you don't want your to damage your CPU after all. Here is a video of Linus delidding a CPU:

L
LauraPoppy
Member
111
07-17-2023, 06:38 PM
#20
Don’t need to open the lid, especially for something already lacking. A $200 CPU is available on eBay right now. The same price as a 3600x model. To get past the lid, you’ll need a pricier tool than a new cooler, so it’s not a free option. Wipe down the old unit with alcohol, apply some good paste, and use a decent cooler (some models include paste). Likely more effective for less money and won’t damage the $200 CPU.
L
LauraPoppy
07-17-2023, 06:38 PM #20

Don’t need to open the lid, especially for something already lacking. A $200 CPU is available on eBay right now. The same price as a 3600x model. To get past the lid, you’ll need a pricier tool than a new cooler, so it’s not a free option. Wipe down the old unit with alcohol, apply some good paste, and use a decent cooler (some models include paste). Likely more effective for less money and won’t damage the $200 CPU.

Pages (3): Previous 1 2 3 Next