Problems with RAM on Ryzen 5 and MSI B450 Tomahawk Max systems

F5F Stay Refreshed Hardware Desktop Problems with RAM on Ryzen 5 and MSI B450 Tomahawk Max systems

Pages (2): 1 2 Next

trilaminat
Junior Member

01-09-2018, 11:50 AM

You're facing some tricky problems with your build setup. It seems the RAM speed settings are conflicting, especially when switching between XMP profiles. The system is trying to enforce a higher speed (3600MHz) but the BIOS resets it back to the default or lower profile (3200MHz). This could be due to BIOS limitations, incorrect XMP profiles, or hardware compatibility issues. Double-check your RAM specifications and ensure they match the motherboard requirements. Also, try disabling XMP temporarily to see if the issue persists. If it does, you might need to adjust BIOS settings or consult the manufacturer's support for further guidance.

trilaminat

01-09-2018, 11:50 AM #1

Spudly44
Junior Member

01-09-2018, 06:01 PM

I removed the CMOS and reset it to BIOS, checked for booting, then adjusted voltage by 0.025V and retried.

Spudly44

01-09-2018, 06:01 PM #2

I removed the CMOS and reset it to BIOS, checked for booting, then adjusted voltage by 0.025V and retried.

Papyrule
Senior Member

560

01-09-2018, 06:09 PM

Adjust the SOC voltage slightly higher and refresh the BIOS. It might be worth checking the IMC, as its performance isn’t great.

Papyrule

01-09-2018, 06:09 PM #3

Adjust the SOC voltage slightly higher and refresh the BIOS. It might be worth checking the IMC, as its performance isn’t great.

ro4o
Junior Member

01-15-2018, 10:33 PM

CMOS was cleared about 35 minutes ago. I encountered the same problem again. Regarding voltage, it's unclear which one is increasing—am I raising the correct value? I confirmed the latest BIOS this morning, and I'm using the BIOS from April of this year.

ro4o

01-15-2018, 10:33 PM #4

SinixYT
Member

224

01-17-2018, 07:23 AM

You can access the advanced settings by adjusting the board configuration. Look for an option labeled "dram voltage" and increase its default value by 0.025v before attempting to boot again.

SinixYT

01-17-2018, 07:23 AM #5

You can access the advanced settings by adjusting the board configuration. Look for an option labeled "dram voltage" and increase its default value by 0.025v before attempting to boot again.

Nixation
Member

222

01-24-2018, 06:42 PM

I'll give it a shot and check the outcome, thanks!

Nixation

01-24-2018, 06:42 PM #6

I'll give it a shot and check the outcome, thanks!

Maximoreyrojo
Member

141

01-24-2018, 09:43 PM

3600 RAM on Zen+ is quite challenging to secure. If it were Zen 2, it would likely function well. Opt for 3200 instead. With Zen+, you won't notice any significant difference when exceeding it.

Maximoreyrojo

01-24-2018, 09:43 PM #7

3600 RAM on Zen+ is quite challenging to secure. If it were Zen 2, it would likely function well. Opt for 3200 instead. With Zen+, you won't notice any significant difference when exceeding it.

LiuvliZ_YT
Junior Member

01-29-2018, 02:32 PM

I adjusted the frequency to 3600mhz, increased the voltage as recommended, and everything is functioning properly now. I can actually launch Windows. How can I better confirm this setup works smoothly without any ongoing issues?

LiuvliZ_YT

01-29-2018, 02:32 PM #8

ToastaStroodel
Member

207

01-29-2018, 10:12 PM

Currently it's functioning well, and I'm looking forward to getting on Zen 2 soon. This 2600 was essentially handed to me, so it matched exactly what I needed from the start.

ToastaStroodel

01-29-2018, 10:12 PM #9

Currently it's functioning well, and I'm looking forward to getting on Zen 2 soon. This 2600 was essentially handed to me, so it matched exactly what I needed from the start.

themadripper
Member

02-03-2018, 02:48 PM

#10

I have comparable specifications too. My 3466MHz CL16 setup functions perfectly.

themadripper

02-03-2018, 02:48 PM #10

I have comparable specifications too. My 3466MHz CL16 setup functions perfectly.

Pages (2): 1 2 Next