F5F Stay Refreshed Hardware Desktop PC is experiencing crashes after 20 to 30 minutes of use.

PC is experiencing crashes after 20 to 30 minutes of use.

PC is experiencing crashes after 20 to 30 minutes of use.

Pages (2): 1 2 Next
G
GamerTale123
Junior Member
19
06-11-2020, 11:36 AM
#1
Hello there. Yesterday I upgraded my PC (actually built a new one, since only a few components were changed – PSU and GPU). While gaming on it, the same issue kept recurring, after about 20 to 30 minutes of play, it would crash. It felt like power was cut off instantly. After a brief pause, everything worked again, but if I disconnect the cable right away, before the LED near the power button goes dark, I can reinsert it and everything functions properly once more. However, if I remove the cable and then reconnect it, the PC doesn’t respond at all, as if the connection had never been made. So far, this has happened only after 20 to 30 minutes of gameplay, and never before.

I used the following components:

Motherboard:
Gigabyte GA-Z97X-Gaming 3
RAM:
Kingston HyperX SAVAGE 4x8GB 2400Mhz
Processor:
Intel Core i5-4690K
Graphics card:
MSI GTX 1080 Ti Gaming X
SSD:
Kingston v300 240GB
HDD:
Western Digital 2 TB (WD20EURX)
PSU:
Corsair RMi RM1000i 1000W
CPU Cooler:
Raijintek THEMIS Evo
Case:
Antec Nine Hundred Two
to
Motherboard:
Gigabyte B550 Gaming x V2
RAM:
G.SKILL Aegis F4-2133C15D-32GIS, DDR4, 32 GB, 3200 MHz
Processor:
AMD 5700x3d
Graphics card:
MSI GTX 1080 Ti Gaming X
Nvme: Kingston SNV3S/500G, M.2 2280, 500 GB
SSD:
Kingston v300 240GB
HDD:
Western Digital 2 TB (WD20EURX)
PSU:
Corsair RMi RM1000i 1000W
CPU Cooler:
Peerless Assassin 120 SE, 125 mm x 155 mm
Case:
MSI MAG FORGE 100R
G
GamerTale123
06-11-2020, 11:36 AM #1

Hello there. Yesterday I upgraded my PC (actually built a new one, since only a few components were changed – PSU and GPU). While gaming on it, the same issue kept recurring, after about 20 to 30 minutes of play, it would crash. It felt like power was cut off instantly. After a brief pause, everything worked again, but if I disconnect the cable right away, before the LED near the power button goes dark, I can reinsert it and everything functions properly once more. However, if I remove the cable and then reconnect it, the PC doesn’t respond at all, as if the connection had never been made. So far, this has happened only after 20 to 30 minutes of gameplay, and never before.

I used the following components:

Motherboard:
Gigabyte GA-Z97X-Gaming 3
RAM:
Kingston HyperX SAVAGE 4x8GB 2400Mhz
Processor:
Intel Core i5-4690K
Graphics card:
MSI GTX 1080 Ti Gaming X
SSD:
Kingston v300 240GB
HDD:
Western Digital 2 TB (WD20EURX)
PSU:
Corsair RMi RM1000i 1000W
CPU Cooler:
Raijintek THEMIS Evo
Case:
Antec Nine Hundred Two
to
Motherboard:
Gigabyte B550 Gaming x V2
RAM:
G.SKILL Aegis F4-2133C15D-32GIS, DDR4, 32 GB, 3200 MHz
Processor:
AMD 5700x3d
Graphics card:
MSI GTX 1080 Ti Gaming X
Nvme: Kingston SNV3S/500G, M.2 2280, 500 GB
SSD:
Kingston v300 240GB
HDD:
Western Digital 2 TB (WD20EURX)
PSU:
Corsair RMi RM1000i 1000W
CPU Cooler:
Peerless Assassin 120 SE, 125 mm x 155 mm
Case:
MSI MAG FORGE 100R

L
levikillerk13
Junior Member
48
06-11-2020, 04:15 PM
#2
I didn't alter the information about the PSU.
PSU details: Corsair RMi RM1000i 1000W.
How old is this PSU?
Your PC stops working when under heavy load? It may shut down due to one of two reasons:
a) Your PC is overheating, or
b) The PSU can't provide enough power for the full system.
You might also face a grounding problem if you need to disconnect and reconnect to the wall.
L
levikillerk13
06-11-2020, 04:15 PM #2

I didn't alter the information about the PSU.
PSU details: Corsair RMi RM1000i 1000W.
How old is this PSU?
Your PC stops working when under heavy load? It may shut down due to one of two reasons:
a) Your PC is overheating, or
b) The PSU can't provide enough power for the full system.
You might also face a grounding problem if you need to disconnect and reconnect to the wall.

S
SophieLlama9
Junior Member
18
06-19-2020, 12:29 PM
#3
Psu should be around 6 to 7 years old. I think it has a warranty for 10 years too.
Technically not really, I finished building it late at night yesterday, so I didn’t even try to use it normally yet—I just played games. After the latest crash, I’m checking if it will happen without playing games. Right now I’m trying to see if it still works when I don’t play. But I can tell you now that the crash happened while I was gaming.
I ran some stress tests for about 10 minutes, first separately then together. Everything worked fine—no crashes. But I’m not sure if that means it wasn’t too much for the system. During the tests, the GPU stayed under 75°C and the CPU slowly reached around 86-90°C, which usually doesn’t happen during normal gaming.
I added this update an hour ago, and so far there’s no crash without playing games. So yes, gaming must be causing something.
S
SophieLlama9
06-19-2020, 12:29 PM #3

Psu should be around 6 to 7 years old. I think it has a warranty for 10 years too.
Technically not really, I finished building it late at night yesterday, so I didn’t even try to use it normally yet—I just played games. After the latest crash, I’m checking if it will happen without playing games. Right now I’m trying to see if it still works when I don’t play. But I can tell you now that the crash happened while I was gaming.
I ran some stress tests for about 10 minutes, first separately then together. Everything worked fine—no crashes. But I’m not sure if that means it wasn’t too much for the system. During the tests, the GPU stayed under 75°C and the CPU slowly reached around 86-90°C, which usually doesn’t happen during normal gaming.
I added this update an hour ago, and so far there’s no crash without playing games. So yes, gaming must be causing something.

T
timo_1892
Senior Member
715
06-19-2020, 12:52 PM
#4
The led next to the power button serves as a hard drive activity indicator. Make sure your front panel connections to the motherboard are correct. Problems often arise due to heat problems. Check that your fan speed settings in the BIOS adjust properly. For testing, remove the case side cover and observe if the issue continues.
T
timo_1892
06-19-2020, 12:52 PM #4

The led next to the power button serves as a hard drive activity indicator. Make sure your front panel connections to the motherboard are correct. Problems often arise due to heat problems. Check that your fan speed settings in the BIOS adjust properly. For testing, remove the case side cover and observe if the issue continues.

E
Erynor
Junior Member
11
06-19-2020, 05:43 PM
#5
Thermal shutdown detected. Reinstall CPU cooler and reapply thermal paste. This is 2133mhz rated RAM—are you overclocking it to 3200mhz? Be aware this may cause instability. Please share screenshots from CPU-Z, specifically the memory and speed sections, by uploading to imgur.com and posting the link.
E
Erynor
06-19-2020, 05:43 PM #5

Thermal shutdown detected. Reinstall CPU cooler and reapply thermal paste. This is 2133mhz rated RAM—are you overclocking it to 3200mhz? Be aware this may cause instability. Please share screenshots from CPU-Z, specifically the memory and speed sections, by uploading to imgur.com and posting the link.

W
Ward12
Posting Freak
895
06-20-2020, 01:24 AM
#6
The blue LED stays on, preventing the PC from turning back on. The only way I managed to shut it down was by disconnecting the PSU wall cable and letting it sit for about 10 seconds.
W
Ward12
06-20-2020, 01:24 AM #6

The blue LED stays on, preventing the PC from turning back on. The only way I managed to shut it down was by disconnecting the PSU wall cable and letting it sit for about 10 seconds.

X
197
06-20-2020, 05:36 AM
#7
I believed it had 3200 ram, but I mistakenly selected the wrong ones. Actually, I use an xmp profile in the bios to achieve 3200.
X
x_HmOoDy_KsA_x
06-20-2020, 05:36 AM #7

I believed it had 3200 ram, but I mistakenly selected the wrong ones. Actually, I use an xmp profile in the bios to achieve 3200.

J
Jerryx01
Posting Freak
870
06-20-2020, 12:28 PM
#8
Link to the screenshots
CPUZ
J
Jerryx01
06-20-2020, 12:28 PM #8

Link to the screenshots
CPUZ

X
XGigaPL
Member
172
06-23-2020, 06:24 AM
#9
This device features an F4-3200C16-16GIS with a 3200mhz rated RAM. (not F4-2133C15D-32GIS)
X
XGigaPL
06-23-2020, 06:24 AM #9

This device features an F4-3200C16-16GIS with a 3200mhz rated RAM. (not F4-2133C15D-32GIS)

T
The_IDK_Face
Junior Member
13
06-24-2020, 01:59 AM
#10
To turn off without unplugging the cords, press and hold the PWR button for about 5 seconds.
Your issue might involve incorrect RAM.
Slot #2 displays a 16gb part number.
The RAM should match for correct functioning.
I suspect you purchased two 16gb sticks with the same number but not a complete set.
Check your RAM
Run
memtest86.
It doesn’t require Windows.
If it completes a full test without errors, you’re probably fine.
For certainty, repeat the process a few more times.
T
The_IDK_Face
06-24-2020, 01:59 AM #10

To turn off without unplugging the cords, press and hold the PWR button for about 5 seconds.
Your issue might involve incorrect RAM.
Slot #2 displays a 16gb part number.
The RAM should match for correct functioning.
I suspect you purchased two 16gb sticks with the same number but not a complete set.
Check your RAM
Run
memtest86.
It doesn’t require Windows.
If it completes a full test without errors, you’re probably fine.
For certainty, repeat the process a few more times.

Pages (2): 1 2 Next