F5F Stay Refreshed Hardware Desktop PC fails to start due to insufficient RAM modules.

PC fails to start due to insufficient RAM modules.

PC fails to start due to insufficient RAM modules.

S
schokomaker356
Junior Member
22
03-30-2017, 05:28 AM
#1
Hello! Here’s a revised version of your text:

Hello! Your system specifications are as follows:
- Memory: Asus TUF B-360 PLUS
- CPU: Intel Core i5-8500
- GPU: Asus DUAL Series GTX 1660 GDDR6 (6GB)
- Power Supply: EVGA 600B Bronze 600W
- Storage: 1TB SSD in an M.2 PCIe slot, plus two 1TB HDDs

I encountered several problems after attempting a RAM upgrade. I purchased two 8GB Adata 3200MHz sticks, but my PC only had one 8GB 2133MHz stick. I followed the manual instructions, placing the dual-channel memory on B2* and A2*. I removed the old RAM from A1 and installed the new ones on A1 and A2. After that, I tried to boot the system. The RAM lights failed to activate, and the PC became unstable with repeated beeping sounds. I didn’t consult the manual for the specific codes, but it never happened again. Later, I moved the memory to B1 and A2*, which should have worked properly.

When I booted again, the PC didn’t even reach POST. The RAM lights turned on, but the GPU fans stopped working, and the system overheated to around 50°C. I eventually removed the B1 stick. Once I reconnected everything, it started working fine. I tried different RAM slots and even removed the GPU temporarily, but nothing changed.

I reset the BIOS settings, removed the GPU (which was covering the battery), and took the battery out for 10 minutes. After reinserting everything, I still couldn’t get past POST. Then I removed one stick to adjust the BIOS settings, lowering the voltage slightly. This was concerning, especially since I’d experienced similar issues before.

Finally, I put the old RAM back in the same position and managed to boot successfully. This time, things improved.
S
schokomaker356
03-30-2017, 05:28 AM #1

Hello! Here’s a revised version of your text:

Hello! Your system specifications are as follows:
- Memory: Asus TUF B-360 PLUS
- CPU: Intel Core i5-8500
- GPU: Asus DUAL Series GTX 1660 GDDR6 (6GB)
- Power Supply: EVGA 600B Bronze 600W
- Storage: 1TB SSD in an M.2 PCIe slot, plus two 1TB HDDs

I encountered several problems after attempting a RAM upgrade. I purchased two 8GB Adata 3200MHz sticks, but my PC only had one 8GB 2133MHz stick. I followed the manual instructions, placing the dual-channel memory on B2* and A2*. I removed the old RAM from A1 and installed the new ones on A1 and A2. After that, I tried to boot the system. The RAM lights failed to activate, and the PC became unstable with repeated beeping sounds. I didn’t consult the manual for the specific codes, but it never happened again. Later, I moved the memory to B1 and A2*, which should have worked properly.

When I booted again, the PC didn’t even reach POST. The RAM lights turned on, but the GPU fans stopped working, and the system overheated to around 50°C. I eventually removed the B1 stick. Once I reconnected everything, it started working fine. I tried different RAM slots and even removed the GPU temporarily, but nothing changed.

I reset the BIOS settings, removed the GPU (which was covering the battery), and took the battery out for 10 minutes. After reinserting everything, I still couldn’t get past POST. Then I removed one stick to adjust the BIOS settings, lowering the voltage slightly. This was concerning, especially since I’d experienced similar issues before.

Finally, I put the old RAM back in the same position and managed to boot successfully. This time, things improved.

P
peraldon
Junior Member
29
03-30-2017, 03:39 PM
#2
50C isn't too hot for a GPU; many will shut off fans when temps drop below 55°C for better efficiency. Focusing on variables helps even if they aren't the real problem. Could the system start with just one dimmer? For example, switching to a dual kit or using the original dimmers—would either work?
P
peraldon
03-30-2017, 03:39 PM #2

50C isn't too hot for a GPU; many will shut off fans when temps drop below 55°C for better efficiency. Focusing on variables helps even if they aren't the real problem. Could the system start with just one dimmer? For example, switching to a dual kit or using the original dimmers—would either work?

I
iiD4nkKid
Junior Member
17
03-31-2017, 12:54 AM
#3
Ensure CMOS is cleared before modifying any parts.
I
iiD4nkKid
03-31-2017, 12:54 AM #3

Ensure CMOS is cleared before modifying any parts.

S
SkullorX
Junior Member
18
03-31-2017, 01:06 PM
#4
Yes, removing the battery for 10 minutes is correct. Done, it's listed in the instructions.
S
SkullorX
03-31-2017, 01:06 PM #4

Yes, removing the battery for 10 minutes is correct. Done, it's listed in the instructions.

Z
Zoleks
Member
237
04-05-2017, 12:22 PM
#5
Currently it doesn't start (at least not with any setup), I'll attempt without the graphics card and share updates here.
Z
Zoleks
04-05-2017, 12:22 PM #5

Currently it doesn't start (at least not with any setup), I'll attempt without the graphics card and share updates here.

S
SrPump11
Member
154
04-07-2017, 07:21 AM
#6
There are jumps available for short. Power loss isn't always resolved.
S
SrPump11
04-07-2017, 07:21 AM #6

There are jumps available for short. Power loss isn't always resolved.