Overclocking Ryzen 3 1200 issue detected, need assistance
Overclocking Ryzen 3 1200 issue detected, need assistance
Hello everyone, I recently switched to Ryzen and am facing challenges with overclocking.
🙁
I ran stress tests multiple times initially at stock speeds and everything performed well on AIDA64 and Cinebench R15 – temperatures stayed below 63°C, the motherboard stayed around 28-32°C, and all readings in CPU-Z and HWmonitor matched consistently. Only one entry labeled "package node 0" showed unusually high values during stress tests, but I found out it was likely an incorrect reading, probably due to a misunderstanding. All components in my system are functioning nicely (my PC is an open case with four fans running).
When attempting overclocking to 3.5–3.9 GHz at voltages between 1.20V and 1.40V in the BIOS, I experience crashes after about 20–30 seconds of stress testing. The screen goes black, and the PC remains unresponsive until I power it off and restart.
I’ve tried adjusting both voltage and clock speed multiple times, but I’m unsure if exceeding 1.4V is safe. If anyone could advise me, I would really appreciate it!
Here are my specifications:
- CPU: AMD Ryzen 3 1200
- GPU: Zotac GTX 750 Ti 2GB GDDR5
- Motherboard: ASRock AB350M PRO 4 (latest BIOS version 3.10)
- RAM: Patriot DDR4 (2x4GB, 8GB, 2400MHz)
- Power Supply: EVGA 430W, 80+ certified
- Hard Drive: Seagate Barracuda 500GB, 7200RPM
Update: After installing Ryzen Master, I attempted overclocking with the same settings. Temperatures matched the package node 0 reading in HWmonitor, which was accurate. However, in AIDA64 it displayed a higher CPU temperature than the motherboard setting (64°C), and after overclocking to 3.5GHz at 1.19375V, the temp spiked to 100°C, forcing me to stop the test.
Any suggestions on what to do? I’ve heard that disabling core boost might improve stability since it reduces voltage fluctuations.
🙁
Thank you very much for your help—I’m hoping this will resolve the issue!
I believe there might be an issue with your cooler or its setup. I have the same motherboard and CPU with a stock cooler that runs at 3.8GHz, 1.2V, and keeps temperatures in the mid-50s even when hitting 60s. At higher speeds, it requires 1.375V which raises the temps to the 90s. I think core boost is automatically turned off around 3.5GHz, though I'm not entirely certain about the exact threshold.
Most ryzens can't operate above 3.9 my dude, only around 15-25% are capable. And if the clock is always running, don't exceed 1.4 volts, and keep the temperature under 80—it's okay as long as it doesn't go past 75. So yeah, most definitely can't go over 3.9GHz.
I believe there might be an issue with your cooler or its setup. I have the same motherboard and CPU with a stock cooler that runs at 3.8GHz, 1.2V, and maintains a temperature around mid-50s. However, when it hits 60s, my temps rise to the 90s. Also, note that going above 3.8V causes temperatures to spike into the 90s. I think core boost is automatically disabled at around 3.5GHz, though I'm not entirely certain about the exact threshold.
I believe there might be an issue with your cooler or its setup. I have the same motherboard and CPU with a stock cooler that runs at 3.8GHz on 1.2V, and the temperature stays around the mid-50s maximum, whereas you're reaching 60s at stock settings. Also, it seems core boost gets turned off automatically when you hit 3.5GHz, though I'm not entirely sure about the exact threshold.
Simon, just a quick note: I recently disassembled my PC and discovered my CPU was only secured with two screws. That’s probably why the temps spiked. Once I tightened everything properly, the temperatures dropped significantly. I’m really impressed!
I think I’ve won the silicon lottery! I successfully overclocked to 3.95GHz at 1.24V. I ran stress tests using Prime95, AIDA64, and Cinebench R15 for more than four hours, and everything held steady with temperatures in the high 50s to mid-60s.
I’m really proud of this achievement!
GOD BLESS YA