F5F Stay Refreshed Hardware Desktop Operating at 3600 MHz with a frequency of 2133

Operating at 3600 MHz with a frequency of 2133

Operating at 3600 MHz with a frequency of 2133

T
tlr13579
Member
178
07-14-2020, 05:55 PM
#1
Hey everyone, I'm using Windows 10 64-bit with a Ryzen 5 5600X and a 32GB G.Skill DDR4 system. My specs are 3600 CL16 KIT (2x16GB) and I'm running the G.VRAM 32G VKC Ripjaws TUF GAMING B550-PLUS RTX 3070. The issue is I see the RAM speed at 2133 MHz in Task Manager, which seems incorrect. After checking the BIOS, DOCP is enabled, but when I exit it, my PC restarts multiple times and enters safe mode until I disable DOCP. Anyone have ideas on how to fix this so I can get full performance?
T
tlr13579
07-14-2020, 05:55 PM #1

Hey everyone, I'm using Windows 10 64-bit with a Ryzen 5 5600X and a 32GB G.Skill DDR4 system. My specs are 3600 CL16 KIT (2x16GB) and I'm running the G.VRAM 32G VKC Ripjaws TUF GAMING B550-PLUS RTX 3070. The issue is I see the RAM speed at 2133 MHz in Task Manager, which seems incorrect. After checking the BIOS, DOCP is enabled, but when I exit it, my PC restarts multiple times and enters safe mode until I disable DOCP. Anyone have ideas on how to fix this so I can get full performance?

F
Fluffycakes123
Senior Member
696
07-20-2020, 04:04 PM
#2
This means the memory overclock (DOCP adjustment) isn't reliable. You might manually set it to 3600Mhz and tweak the timings, or opt for a lower frequency like 3200MHz. Do you have other DOCP profiles available to select?
F
Fluffycakes123
07-20-2020, 04:04 PM #2

This means the memory overclock (DOCP adjustment) isn't reliable. You might manually set it to 3600Mhz and tweak the timings, or opt for a lower frequency like 3200MHz. Do you have other DOCP profiles available to select?

A
AdamKoudy
Senior Member
740
07-20-2020, 07:12 PM
#3
It is the only choice available: "Profile 1" and "Disabled".
A
AdamKoudy
07-20-2020, 07:12 PM #3

It is the only choice available: "Profile 1" and "Disabled".

B
Blue51
Member
65
08-05-2020, 12:52 AM
#4
Adjust the memory frequency to around 3200MHz, restart the system and check stability. If it works, raise the frequency gradually until issues appear, then slightly lower it for safety. Or, set it to 3600MHz and fine-tune timing and voltage manually.
B
Blue51
08-05-2020, 12:52 AM #4

Adjust the memory frequency to around 3200MHz, restart the system and check stability. If it works, raise the frequency gradually until issues appear, then slightly lower it for safety. Or, set it to 3600MHz and fine-tune timing and voltage manually.

C
CitchoR
Junior Member
34
08-11-2020, 10:29 AM
#5
Review the recommended slots you need to use (Motherboard Manual). Certain boards may require specific DIMM setups that others don’t. Slots 1, 2, 3, and 4 are common, but the board might prefer configurations like 1&3, 1&2, or 2&4 to achieve advertised speeds.
C
CitchoR
08-11-2020, 10:29 AM #5

Review the recommended slots you need to use (Motherboard Manual). Certain boards may require specific DIMM setups that others don’t. Slots 1, 2, 3, and 4 are common, but the board might prefer configurations like 1&3, 1&2, or 2&4 to achieve advertised speeds.

I
iKegreenS_
Posting Freak
878
08-12-2020, 11:24 AM
#6
I
iKegreenS_
08-12-2020, 11:24 AM #6

L
loick3333
Member
119
08-13-2020, 04:57 PM
#7
Yup. This was the reason. I had the sticks in A1/B1. Put them in A2/B2, turned on DOCP and it works. Thank you, Sir! And of course thanks to @The_russian and @Spotty aswell!
L
loick3333
08-13-2020, 04:57 PM #7

Yup. This was the reason. I had the sticks in A1/B1. Put them in A2/B2, turned on DOCP and it works. Thank you, Sir! And of course thanks to @The_russian and @Spotty aswell!