F5F Stay Refreshed Hardware Desktop Not supported. Is there anything else you need?

Not supported. Is there anything else you need?

Not supported. Is there anything else you need?

I
iMegaan
Member
Find
162
01-23-2016, 03:32 AM
#1
Hello, I'm setting up a PC using a B660M-A Wi-Fi card from MSI. When trying to install the CMK32GX4M2D3000C16 RAM, it only works with one of the two sticks. Probably it wasn't supported at all... Should I replace my RAM? My system has an Intel Core i5 12400F GTX 1660.
Reply
Reply
I
iMegaan
01-23-2016, 03:32 AM #1

Hello, I'm setting up a PC using a B660M-A Wi-Fi card from MSI. When trying to install the CMK32GX4M2D3000C16 RAM, it only works with one of the two sticks. Probably it wasn't supported at all... Should I replace my RAM? My system has an Intel Core i5 12400F GTX 1660.

Reply
Reply
B
ByxLive
Member
Find
102
01-24-2016, 02:06 AM
#2
It hinges on how you define "supported." Usually, if the RAM matches the board's requirements—like DDR4 for a compatible system—it should work well, though performance might not match the rated speeds.
Reply
Reply
B
ByxLive
01-24-2016, 02:06 AM #2

It hinges on how you define "supported." Usually, if the RAM matches the board's requirements—like DDR4 for a compatible system—it should work well, though performance might not match the rated speeds.

Reply
Reply
G
goldfer1
Member
Find
60
02-08-2016, 11:59 PM
#3
Sure, it sounds like once you inserted the second stick, the system stopped starting, regardless of the settings you tried.
Reply
Reply
G
goldfer1
02-08-2016, 11:59 PM #3

Sure, it sounds like once you inserted the second stick, the system stopped starting, regardless of the settings you tried.

Reply
Reply
J
jolien_x
Junior Member
Find
45
02-10-2016, 03:44 PM
#4
The RAM is operating at a consistent speed, but it might not match the expected two-stick configuration. It's a good idea to verify both sticks separately to ensure the system boots properly with each individually.
Reply
Reply
J
jolien_x
02-10-2016, 03:44 PM #4

The RAM is operating at a consistent speed, but it might not match the expected two-stick configuration. It's a good idea to verify both sticks separately to ensure the system boots properly with each individually.

Reply
Reply
C
ChibiWolf39
Senior Member
Find
491
02-12-2016, 09:54 AM
#5
Hey, the setup is at 3000MHz and both sticks are functional. I’d consider tweaking BIOS settings, though it looks like MSI blocked me from doing so—boot shows a delay of about half a second before Windows loads.
Reply
Reply
C
ChibiWolf39
02-12-2016, 09:54 AM #5

Hey, the setup is at 3000MHz and both sticks are functional. I’d consider tweaking BIOS settings, though it looks like MSI blocked me from doing so—boot shows a delay of about half a second before Windows loads.

Reply
Reply
M
Miyuumi
Senior Member
Find
543
02-14-2016, 08:23 AM
#6
If you can access BIOS, modify the RAM speed to 2933 rather than 3000. Consider checking whether it's actually operating at 3000. Also, verify if XMP is turned on.
Reply
Reply
M
Miyuumi
02-14-2016, 08:23 AM #6

If you can access BIOS, modify the RAM speed to 2933 rather than 3000. Consider checking whether it's actually operating at 3000. Also, verify if XMP is turned on.

Reply
Reply
A
alexandre6768
Member
Find
219
03-05-2016, 05:04 AM
#7
The feature was set to active by default; I'll attempt to turn it off to check its functionality.
Reply
Reply
A
alexandre6768
03-05-2016, 05:04 AM #7

The feature was set to active by default; I'll attempt to turn it off to check its functionality.

Reply
Reply
D
Dolphin029
Junior Member
Find
18
03-05-2016, 01:32 PM
#8
Other suggestions? Let's explore further options.
Reply
Reply
D
Dolphin029
03-05-2016, 01:32 PM #8

Other suggestions? Let's explore further options.

Reply
Reply
J
JorgeSancho
Member
Find
227
03-10-2016, 12:12 PM
#9
Try resetting the CMOS by removing the battery from the motherboard. Check for a clear CMOS jumper—usually two pins that can be shorted. Always disconnect the computer beforehand. If no jumper exists, simply hold the power button down while the battery is removed and the device is unplugged.
Reply
Reply
J
JorgeSancho
03-10-2016, 12:12 PM #9

Try resetting the CMOS by removing the battery from the motherboard. Check for a clear CMOS jumper—usually two pins that can be shorted. Always disconnect the computer beforehand. If no jumper exists, simply hold the power button down while the battery is removed and the device is unplugged.

Reply
Reply
I
ishpish2
Member
Find
60
03-12-2016, 09:38 PM
#10
Unfortunately, that didn't work either...
Reply
Reply
I
ishpish2
03-12-2016, 09:38 PM #10

Unfortunately, that didn't work either...

Reply
Reply