F5F Stay Refreshed Power Users Networks New Router

New Router

New Router

H
hotmeme
Junior Member
7
12-04-2020, 12:32 PM
#1
Hey everyone, I'm considering upgrading to a new router for my home setup. My current device lacks bandwidth control, which causes lag when others download during games. It's an AIO Wi-Fi router connected via ADSL at 25Mbps—my parents cover the costs, so I can afford this. My device uses the 10.0.x.x range, and the router will likely default to 192.168.x.x. Should I keep them on the same IP network or separate them? I expect a DHCP conflict but can disable it from one router. It's not a big concern since I'll have up to 15 devices online. No need for complex subnet settings.
H
hotmeme
12-04-2020, 12:32 PM #1

Hey everyone, I'm considering upgrading to a new router for my home setup. My current device lacks bandwidth control, which causes lag when others download during games. It's an AIO Wi-Fi router connected via ADSL at 25Mbps—my parents cover the costs, so I can afford this. My device uses the 10.0.x.x range, and the router will likely default to 192.168.x.x. Should I keep them on the same IP network or separate them? I expect a DHCP conflict but can disable it from one router. It's not a big concern since I'll have up to 15 devices online. No need for complex subnet settings.

U
UnderZero17
Member
124
12-08-2020, 11:11 AM
#2
Start with your primary goal when doubling the NAT—aim for separate subnets. For future setup, consider switching the modem to a bridged configuration if you intend to add a router. Next, think about your bandwidth management strategy.
U
UnderZero17
12-08-2020, 11:11 AM #2

Start with your primary goal when doubling the NAT—aim for separate subnets. For future setup, consider switching the modem to a bridged configuration if you intend to add a router. Next, think about your bandwidth management strategy.

S
Simon_303
Member
169
12-15-2020, 08:28 AM
#3
Most routers sold ready-to-use let you define your desired LAN IP range. The challenge arises when connecting to another router on the same network, like your AIO device or gateway. Both devices may try to handle each other's tasks, causing conflicts. To resolve this, enable "bridge" mode if supported, and link your new router directly via Ethernet to the gateway. Set up its settings as you normally would—QoS, wireless, etc.—so client devices join the new router’s access point while the gateway remains only for connecting to the DSL line. You’ll need access to the gateway’s admin panel with valid credentials. Not every gateway supports this feature easily; I used a cable ISP device that let me disable its Wi-Fi and assign a static IP to my new router’s MAC address. Then I connected the new router directly over Ethernet, configured it as needed, and everything functioned smoothly. Ideally, keep this network on a separate subnet from the AIO gateway to avoid recurring issues. So far, this setup has worked well for me. I used an Ubiquiti Edgerouter X-SFP for routing, firewall, QOS, and paired two UAP-ACs for access points. After tweaking the QoS settings, the network responded quickly, even with many connected clients.
S
Simon_303
12-15-2020, 08:28 AM #3

Most routers sold ready-to-use let you define your desired LAN IP range. The challenge arises when connecting to another router on the same network, like your AIO device or gateway. Both devices may try to handle each other's tasks, causing conflicts. To resolve this, enable "bridge" mode if supported, and link your new router directly via Ethernet to the gateway. Set up its settings as you normally would—QoS, wireless, etc.—so client devices join the new router’s access point while the gateway remains only for connecting to the DSL line. You’ll need access to the gateway’s admin panel with valid credentials. Not every gateway supports this feature easily; I used a cable ISP device that let me disable its Wi-Fi and assign a static IP to my new router’s MAC address. Then I connected the new router directly over Ethernet, configured it as needed, and everything functioned smoothly. Ideally, keep this network on a separate subnet from the AIO gateway to avoid recurring issues. So far, this setup has worked well for me. I used an Ubiquiti Edgerouter X-SFP for routing, firewall, QOS, and paired two UAP-ACs for access points. After tweaking the QoS settings, the network responded quickly, even with many connected clients.

K
KK10CRAFT
Junior Member
2
12-15-2020, 09:38 AM
#4
I'll provide my sibling with 2048Kbps for both incoming and outgoing data.
K
KK10CRAFT
12-15-2020, 09:38 AM #4

I'll provide my sibling with 2048Kbps for both incoming and outgoing data.

C
CharalPT
Junior Member
5
12-17-2020, 07:59 AM
#5
The main issue is the upload. Using ADSL with only a meg upload keeps the problem ongoing. Going even lower will only increase it by causing more retransmissions over time.
C
CharalPT
12-17-2020, 07:59 AM #5

The main issue is the upload. Using ADSL with only a meg upload keeps the problem ongoing. Going even lower will only increase it by causing more retransmissions over time.