LAN connection only functions at 10Mbps on this Asrock B550M pro4 motherboard.
LAN connection only functions at 10Mbps on this Asrock B550M pro4 motherboard.
unicorn520
04-26-2021, 05:44 AM #11It's fine, I've shared the full log. Please confirm if you want it posted here. I've enabled auto-negotiation and tested it at 1Gbps, but no results were obtained.
Take that program off your system. It's unnecessary. Back in the days of Windows XP and older gear like dial-up, ADSL modems, and routers, those tools helped boost internet performance. Now Windows settings are much more efficient, likely surpassing what this software could achieve. Moreover, any tweaks you make only apply to connections between your machine and the ISP's modem—so it's pointless. First remove it, then check Device Manager: right-click the Realtek driver, choose Uninstall, restart. This might fix issues if the software had linked extra drivers to your network card. After rebooting, open Device Manager, select Scan for hardware changes from the menu (or similar), and the network card driver should be reinstalled. The advanced settings differ by chip model and motherboard; it's normal you don't have all options. Your connection speed is listed at 10 Mbps, which isn't a bottleneck—it means the software isn't overloading the link. Your Ethernet card might be intentionally capped at 10 Mbps for compatibility. Possible causes include faulty cables, poor connectors, high error rates during data transfer, or even brief power interruptions that confuse the chip. If you set the speed to 1 Gbps, it won't work because the other side can only handle 100 Mbps; the card will default back to 10 Mbps. If you choose 100 Mbps full duplex or half duplex (full duplex preferred), and the router supports it, you'll get a full 100 Mbps.
[Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! powershell.exe Set-NetOffloadGlobalSetting -ReceiveSegmentCoalescing enabled !!!-------------------!!! PowerShell.exe Disable-NetAdapterLso -Name * !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -EcnCapability default Set-NetTCPSetting : Cannot process argument transformation on parameter 'EcnCapability'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.EcnCapability". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled" At line:1 char:56 + Set-NetTCPSetting -SettingName internet -EcnCapability default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -Timestamps default Set-NetTCPSetting : Cannot process argument transformation on parameter 'Timestamps'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.Timestamps". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled, Allowed" At line:1 char:53 + Set-NetTCPSetting -SettingName internet -Timestamps default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -NonSackRttResiliency default Set-NetTCPSetting : Cannot process argument transformation on parameter 'NonSackRttResiliency'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.NonSackRttResiliency". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled" At line:1 char:63 + Set-NetTCPSetting -SettingName internet -NonSackRttResiliency default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -InitialRto 3000 !!!-------------------!!! netsh interface ipv4 set subinterface "Ethernet" mtu=1500 store=persistent Ok. !!!-------------------!!! netsh interface ipv6 set subinterface "Ethernet" mtu=1500 store=persistent Ok. !!!-------------------!!! netsh interface ipv4 set subinterface "Ethernet 2" mtu=1500 store=persistent Element not found. !!!-------------------!!! netsh interface ipv6 set subinterface "Ethernet 2" mtu=1500 store=persistent Element not found. !!!-------------------!!! netsh int ip show interfaces Idx Met MTU State Name --- ---------- ---------- ------------ --------------------------- 1 75 4294967295 connected Loopback Pseudo-Interface 1 16 25 1500 disconnected Wi-Fi 18 35 1500 connected Ethernet 2 25 1500 disconnected Local Area Connection* 9 6 25 1500 disconnected Local Area Connection* 10 !!!-------------------!!! PowerShell.exe Get-NetAdapterLso -Name '*' Name Version V1IPv4Enabled IPv4Enabled IPv6Enabled ---- ------- ------------- ----------- ----------- Ethernet LSO Version 2 False False False !!!-------------------!!! PowerShell.exe Get-NetAdapterChecksumOffload '*' Name IpIPv4Enabled TcpIPv4Enabled TcpIPv6Enabled UdpIPv4Enabled UdpIPv6Enabled ---- ------------- -------------- -------------- -------------- -------------- Ethernet RxTxEnabled RxTxEnabled RxTxEnabled RxTxEnabled RxTxEnabled !!!-------------------!!! PowerShell.exe Get-NetTCPSetting -SettingName internet SettingName : Internet MinRto(ms) : 300 InitialCongestionWindow(MSS) : 10 CongestionProvider : CUBIC CwndRestart : False DelayedAckTimeout(ms) : 40 DelayedAckFrequency : 2 MemoryPressureProtection : Enabled AutoTuningLevelLocal : Normal AutoTuningLevelGroupPolicy : NotConfigured AutoTuningLevelEffective : Local EcnCapability : Disabled Timestamps : Disabled InitialRto(ms) : 3000 ScalingHeuristics : Disabled DynamicPortRangeStartPort : 49152 DynamicPortRangeNumberOfPorts : 16384 AutomaticUseCustom : Disabled NonSackRttResiliency : Disabled ForceWS : Enabled MaxSynRetransmissions : 2 AutoReusePortRangeStartPort : 0 AutoReusePortRangeNumberOfPorts : 0 !!!-------------------!!! netsh int tcp show global Querying active state... TCP Global Parameters ---------------------------------------------- Receive-Side Scaling State : enabled Receive Window Auto-Tuning Level : normal Add-On Congestion Control Provider : default ECN Capability : disabled RFC 1323 Timestamps : disabled Initial RTO : 3000 Receive Segment Coalescing State : enabled Non Sack Rtt Resiliency : disabled Max SYN Retransmissions : 2 Fast Open : enabled Fast Open Fallback : enabled HyStart : enabled Proportional Rate Reduction : enabled Pacing Profile : off !!!-------------------!!! PowerShell.exe Get-NetOffloadGlobalSetting ReceiveSideScaling : Enabled ReceiveSegmentCoalescing : Enabled Chimney : Disabled TaskOffload : Enabled NetworkDirect : Enabled NetworkDirectAcrossIPSubnets : Blocked PacketCoalescingFilter : Enabled
WoofyMonster
04-28-2021, 11:59 AM #13Hi mate, Thanks for reply the optimizer tools doesn't change any driver settings no worries about it and like many suggested i've deleted it cause its a powershell gui kinda interface >>>anyway i'm posting the logs of it since somany have asked for it..and yes the connection change in advance tab changes the connection to 100Mbps but i'm not reciving any internet & i'm unable to even log in the router page ...but in linux(i've used a usb bootable linux) it shows as 10Mbps as default too...could it be a hardware problem??? Windows 10 Pro (64-bit) Build:22631 10.2 03.07.2024 14:28:05 !!!-------------------!!! netsh int tcp show supplemental The TCP global default template is internet TCP Supplemental Parameters ---------------------------------------------- Minimum RTO (msec) : 300 Initial Congestion Window (MSS) : 10 Congestion Control Provider : cubic Enable Congestion Window Restart : disabled Delayed ACK timeout (msec) : 40 Delayed ACK frequency : 2 Enable RACK : enabled Enable Tail Loss Probe : enabled Please use the 'netsh int tcp show supplementalports' and 'netsh int tcp show supplementalsubnets' commands to view active filters. !!!-------------------!!! netsh int ip show interfaces Idx Met MTU State Name --- ---------- ---------- ------------ --------------------------- 1 75 4294967295 connected Loopback Pseudo-Interface 1 16 25 1500 disconnected Wi-Fi 18 35 1000 connected Ethernet 2 25 1500 disconnected Local Area Connection* 9 !!!-------------------!!! PowerShell.exe Get-NetAdapterLso -Name '*' Name Version V1IPv4Enabled IPv4Enabled IPv6Enabled ---- ------- ------------- ----------- ----------- Ethernet LSO Version 2 False False False !!!-------------------!!! PowerShell.exe Get-NetAdapterChecksumOffload '*' Name IpIPv4Enabled TcpIPv4Enabled TcpIPv6Enabled UdpIPv4Enabled UdpIPv6Enabled ---- ------------- -------------- -------------- -------------- -------------- Ethernet RxTxEnabled RxTxEnabled RxTxEnabled RxTxEnabled RxTxEnabled !!!-------------------!!! PowerShell.exe Get-NetTCPSetting -SettingName internet SettingName : Internet MinRto(ms) : 300 InitialCongestionWindow(MSS) : 10 CongestionProvider : CUBIC CwndRestart : False DelayedAckTimeout(ms) : 40 DelayedAckFrequency : 2 MemoryPressureProtection : Enabled AutoTuningLevelLocal : Normal AutoTuningLevelGroupPolicy : NotConfigured AutoTuningLevelEffective : Local EcnCapability : Disabled Timestamps : Disabled InitialRto(ms) : 2000 ScalingHeuristics : Disabled DynamicPortRangeStartPort : 49152 DynamicPortRangeNumberOfPorts : 16384 AutomaticUseCustom : Disabled NonSackRttResiliency : Disabled ForceWS : Enabled MaxSynRetransmissions : 2 AutoReusePortRangeStartPort : 0 AutoReusePortRangeNumberOfPorts : 0 !!!-------------------!!! netsh int tcp show global Querying active state... TCP Global Parameters ---------------------------------------------- Receive-Side Scaling State : enabled Receive Window Auto-Tuning Level : normal Add-On Congestion Control Provider : default ECN Capability : disabled RFC 1323 Timestamps : disabled Initial RTO : 2000 Receive Segment Coalescing State : disabled Non Sack Rtt Resiliency : disabled Max SYN Retransmissions : 2 Fast Open : enabled Fast Open Fallback : enabled HyStart : enabled Proportional Rate Reduction : enabled Pacing Profile : off !!!-------------------!!! PowerShell.exe Get-NetOffloadGlobalSetting ReceiveSideScaling : Enabled ReceiveSegmentCoalescing : Disabled Chimney : Disabled TaskOffload : Enabled NetworkDirect : Enabled NetworkDirectAcrossIPSubnets : Blocked PacketCoalescingFilter : Enabled !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -ScalingHeuristics default Set-NetTCPSetting : Cannot process argument transformation on parameter 'ScalingHeuristics'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.ScalingHeuristics". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled" At line:1 char:60 + Set-NetTCPSetting -SettingName internet -ScalingHeuristics default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! powershell.exe Set-NetOffloadGlobalSetting -ReceiveSegmentCoalescing enabled !!!-------------------!!! PowerShell.exe Disable-NetAdapterLso -Name * !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -EcnCapability default Set-NetTCPSetting : Cannot process argument transformation on parameter 'EcnCapability'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.EcnCapability". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled" At line:1 char:56 + Set-NetTCPSetting -SettingName internet -EcnCapability default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -Timestamps default Set-NetTCPSetting : Cannot process argument transformation on parameter 'Timestamps'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.Timestamps". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled, Allowed" At line:1 char:53 + Set-NetTCPSetting -SettingName internet -Timestamps default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -NonSackRttResiliency default Set-NetTCPSetting : Cannot process argument transformation on parameter 'NonSackRttResiliency'. Cannot convert value "default" to type "Microsoft.PowerShell.Cmdletization.GeneratedTypes.NetTCPSetting.NonSackRttResiliency". Error: "Unable to match the identifier name default to a valid enumerator name. Specify one of the following enumerator names and try again: Disabled, Enabled" At line:1 char:63 + Set-NetTCPSetting -SettingName internet -NonSackRttResiliency default + ~~~~~~~ + CategoryInfo : InvalidData: ( [Set-NetTCPSetting], ParameterBindingArgumentTransformationException + FullyQualifiedErrorId : ParameterArgumentTransformationError,Set-NetTCPSetting !!!-------------------!!! PowerShell.exe Set-NetTCPSetting -SettingName internet -InitialRto 3000 !!!-------------------!!! netsh interface ipv4 set subinterface "Ethernet" mtu=1500 store=persistent Ok. !!!-------------------!!! netsh interface ipv6 set subinterface "Ethernet" mtu=1500 store=persistent Ok. !!!-------------------!!! netsh interface ipv4 set subinterface "Ethernet 2" mtu=1500 store=persistent Element not found. !!!-------------------!!! netsh interface ipv6 set subinterface "Ethernet 2" mtu=1500 store=persistent Element not found. !!!-------------------!!! netsh int ip show interfaces Idx Met MTU State Name --- ---------- ---------- ------------ --------------------------- 1 75 4294967295 connected Loopback Pseudo-Interface 1 16 25 1500 disconnected Wi-Fi 18 35 1500 connected Ethernet 2 25 1500 disconnected Local Area Connection* 9 6 25 1500 disconnected Local Area Connection* 10 !!!-------------------!!! PowerShell.exe Get-NetAdapterLso -Name '*' Name Version V1IPv4Enabled IPv4Enabled IPv6Enabled ---- ------- ------------- ----------- ----------- Ethernet LSO Version 2 False False False !!!-------------------!!! PowerShell.exe Get-NetAdapterChecksumOffload '*' Name IpIPv4Enabled TcpIPv4Enabled TcpIPv6Enabled UdpIPv4Enabled UdpIPv6Enabled ---- ------------- -------------- -------------- -------------- -------------- Ethernet RxTxEnabled RxTxEnabled RxTxEnabled RxTxEnabled RxTxEnabled !!!-------------------!!! PowerShell.exe Get-NetTCPSetting -SettingName internet SettingName : Internet MinRto(ms) : 300 InitialCongestionWindow(MSS) : 10 CongestionProvider : CUBIC CwndRestart : False DelayedAckTimeout(ms) : 40 DelayedAckFrequency : 2 MemoryPressureProtection : Enabled AutoTuningLevelLocal : Normal AutoTuningLevelGroupPolicy : NotConfigured AutoTuningLevelEffective : Local EcnCapability : Disabled Timestamps : Disabled InitialRto(ms) : 3000 ScalingHeuristics : Disabled DynamicPortRangeStartPort : 49152 DynamicPortRangeNumberOfPorts : 16384 AutomaticUseCustom : Disabled NonSackRttResiliency : Disabled ForceWS : Enabled MaxSynRetransmissions : 2 AutoReusePortRangeStartPort : 0 AutoReusePortRangeNumberOfPorts : 0 !!!-------------------!!! netsh int tcp show global Querying active state... TCP Global Parameters ---------------------------------------------- Receive-Side Scaling State : enabled Receive Window Auto-Tuning Level : normal Add-On Congestion Control Provider : default ECN Capability : disabled RFC 1323 Timestamps : disabled Initial RTO : 3000 Receive Segment Coalescing State : enabled Non Sack Rtt Resiliency : disabled Max SYN Retransmissions : 2 Fast Open : enabled Fast Open Fallback : enabled HyStart : enabled Proportional Rate Reduction : enabled Pacing Profile : off !!!-------------------!!! PowerShell.exe Get-NetOffloadGlobalSetting ReceiveSideScaling : Enabled ReceiveSegmentCoalescing : Enabled Chimney : Disabled TaskOffload : Enabled NetworkDirect : Enabled NetworkDirectAcrossIPSubnets : Blocked PacketCoalescingFilter : Enabled
fish_tommy
04-29-2021, 10:51 PM #14I've shared some photos of the final setup after all the recommendations. The inspection images are already posted, and the port cable appears fine. I disabled the LAN port, removed the Wi-Fi service, and used the Realtek drivers from their website (Realtek_LAN version 10.060.0615.2022). Also installed the AsRock driver for Windows 11 and Windows 10. The installer kept suggesting a repair option each time it opened after another was installed. I confirmed the Advanced Tab is set to auto-negotiate, but the connection still changes to 100Mbps yet no internet is working, and I can't access the router admin page.
Do you have another cable to test? I’m skeptical about this one because the crimp at the bottom is meant to secure the cable sheathing and stop wires from being pulled when the cable shifts, but it’s being crimped incorrectly onto the wires themselves, which won’t hold them in place. I’ve made a similar error before and it always led to poor connections. Be sure to clean the port thoroughly using a Q tip and 99% isopropyl alcohol just in case. Make sure you only move forward to back as the Q tip could get caught if you try to reverse the direction.
Hi, Yes i've tried with a different cable, which is not like self made but a inbuilding wiring one which is laminated good one but the result is kinda same no change/no internet when 100Mbps or 1000Mbps is forced in pc/router settings...i'll try the clean with earbuds i'll u know...
The modem supports 1000Mbps full duplex, yet the connection is restricted to a 50Mbps plan. I can adjust the settings in the modem, but increasing the LAN speed won’t work. I’ve modified the TCP/IPv4 configuration, though the default settings appear active. However, the screenshot shows internet connected at 100Mbps while actual data packets are minimal or absent. I’ve also tested it on Ubuntu 22.04, forcing the LAN port to 100Mbps, but it still didn’t connect. It seems there might be a hardware issue. Additionally, using a different modem (Dlink-650IN) only achieves 10Mbps.