I've been dealing with many BSODs over the last week and a half!
I've been dealing with many BSODs over the last week and a half!
You lack a compatible set of RAM.
RAM comes in kits for a reason.
A motherboard needs to handle all the RAM according to the same voltage, case, and speed specifications.
The internal design is tailored for the capacity of the kit.
RAM from the same manufacturer and part number may vary in manufacturing over time.
Certain motherboards are particularly sensitive to these changes.
This becomes more challenging with multiple modules.
RAM must be compatible for optimal performance.
Ryzen efficiency is closely linked to RAM capacity.
Your previous upgrade might have succeeded, but it doesn’t seem to now.
The best advice is to install two sticks and configure the settings explicitly for the speed and timings you desire, while choosing a higher voltage than the original.
Hi Ralston, I’m going to check my PC now and examine those two areas. Sadly, I do monitor those spots, and I believe I would have identified the issue if it were more obvious there. Still, I’ll revisit them, share a picture, and gather more details. Also, I’ll update my post with my PC information. Thanks for your prompt reply!
Hi Ralston, I made sure to add any details I could think of. If you think I need more specifics, I’ll do my best to locate them. Right now, would it be better to start with Windows Memory Diagnostic, and if needed, run Memtest afterward? I saw that approach is common, as mentioned in the post. Unfortunately, I can’t physically disassemble my PC like before because of physical limitations, so I’m hoping this RAM check will be the most helpful step using what I’ve shared.
Today I encountered the MEMORY_MANAGEMENT BSODs and realized my memory issues, even at 3970 MHz, affecting it to 4266. The next day I faced problems with Firefox not launching. Test your memory; I recommend Prime95 with large FFTs.
I'll wait to hear what others say before trying Prime95, as I don't believe it will help. As you mentioned, I've run several stress tests using Heaven, played demanding games, and never experienced BSODs during those sessions. These crashes only occurred when launching or downloading games, but the issue isn't with my disks—CHKDSK and Disk Management confirmed everything is fine.
Also, thank you for your response to my post!
This motherboard?
https://download-2.msi.com/archive/mnu_e...MAHAWK.pdf
Make sure you have the correct User Manual for it.
Go through the whole document and all related files carefully. Focus on every small detail, warnings, and online update references.
= = = =
Some motherboards need the first RAM slot to be filled with DIMM_A2 physically.
The linked User Manual specifies this as a requirement for your board.
Check page 15 which is marked as physically numbered.
Also, note seven other important notes that must be followed.
Verify everything thoroughly to confirm it meets all expectations.
Hi Ralston. I revisited the manual and went through the pages again, focusing on page 15. After checking each step carefully, I didn’t find any apparent issues. For instance, my RAM voltage is correctly set at 1.36V at 3200 MHz, and it’s properly seated in the A & C, B & D slots. Yet, after running a full Windows Memory Diagnostic test, it flagged a hardware issue right away. Here are the test results. If the problem was detected so quickly, could it be that the RAM isn’t fully seated?
Quick update. I went ahead and started memtest86 and decided to just have all four sticks in there just to see if there were any issues immediately. Well, I did end up having errors not even a minute after starting.
I’ll have someone help me with reseating the RAM in a little while. Would anyone know what this error indicates?
What is the model of your RAM package?
Is it a complete set that matches?
If not, it may lead to complications.
The CPU-Z speed section will show the installed part number.
Check all four options.
You could fix the problem by adjusting the voltage settings in the motherboard BIOS.
I possess two pairs of 2 x 8 Corsair Vengenace 3200Mhz XMP modules that have functioned smoothly together for almost three years. I began with just one pair when constructing my PC, then acquired the identical model a year later, and it performed well. That’s all I can share at this point, as I’m currently running the PC through Memtest86 to determine if the problem lies with the RAM, the slot, or possibly the CPU.
I’ll keep updating my discussion here with my findings.
Please forgive any confusion in my responses and my current choices. I’m ready to wrap up this process. If it provides any insight, I’ve verified the RAM using the original 2133 MHz configuration with 1.2V (BIOS default unchanged) and also tested at 3200Mhz, which adjusted to 1.36V. Despite this, I consistently encountered BSODs.
Since these have always worked with my old motherboard and CPU for years, the sudden errors after switching components suggest one of the issues mentioned earlier.
Throughout this, all four RAM slots in the PC generated thousands of errors. After re-seating each stick individually, the issue persisted, with the entire set showing errors within ten seconds.
Thank you for your reply!