F5F Stay Refreshed Hardware Desktop Issue with New AM5 Model Failing Post-Processing

Issue with New AM5 Model Failing Post-Processing

Issue with New AM5 Model Failing Post-Processing

L
Leyhaya
Posting Freak
801
11-15-2022, 12:59 AM
#1
Ryzen 7900 ASRock B650M Pro RS Wifi with g.skill Flare X 2x16GB DDR5 6000 CL30 and EVGA 550W. All other components are disconnected except the CPU cooler. The CPU and DRAM indicators remain consistently red when I post.

Actions taken:
- Checked RAM modules individually in each slot
- Updated BIOS to the latest version
- Reset CMOS

Possible hints:
- Power supply appears to be functioning properly for the fan
- CPU cooler fins are cool, no voltage detected on the CPU
- Connecting two case fans in series caused the rear fan to spin normally, but the Arctic PWM PST fan showed slight jitter when power was applied
L
Leyhaya
11-15-2022, 12:59 AM #1

Ryzen 7900 ASRock B650M Pro RS Wifi with g.skill Flare X 2x16GB DDR5 6000 CL30 and EVGA 550W. All other components are disconnected except the CPU cooler. The CPU and DRAM indicators remain consistently red when I post.

Actions taken:
- Checked RAM modules individually in each slot
- Updated BIOS to the latest version
- Reset CMOS

Possible hints:
- Power supply appears to be functioning properly for the fan
- CPU cooler fins are cool, no voltage detected on the CPU
- Connecting two case fans in series caused the rear fan to spin normally, but the Arctic PWM PST fan showed slight jitter when power was applied

L
luk321
Member
209
11-15-2022, 09:49 AM
#2
model of this evga 500w?
L
luk321
11-15-2022, 09:49 AM #2

model of this evga 500w?

R
Rok_ka
Member
146
11-20-2022, 05:32 AM
#3
With XMP/EXPO overclocking active at 6000, consider disabling it. The system tends to start up using the JEDEC standard RAM rate.
R
Rok_ka
11-20-2022, 05:32 AM #3

With XMP/EXPO overclocking active at 6000, consider disabling it. The system tends to start up using the JEDEC standard RAM rate.

C
CreeperRocket1
Member
210
11-28-2022, 09:38 AM
#4
EVGA SuperNOVA 550 G3, 80 Plus Gold
Purchased it a few years back, and this is my first use. I looked into testing it by connecting the green pin to black/ground with a paper clip, and I plan to try that again.
Edit: G3, not GA.
C
CreeperRocket1
11-28-2022, 09:38 AM #4

EVGA SuperNOVA 550 G3, 80 Plus Gold
Purchased it a few years back, and this is my first use. I looked into testing it by connecting the green pin to black/ground with a paper clip, and I plan to try that again.
Edit: G3, not GA.

A
Aldiin_
Junior Member
42
11-29-2022, 12:46 AM
#5
I haven't managed to operate the board beyond a successful flashback. It doesn't start or display the UEFI screen.
A
Aldiin_
11-29-2022, 12:46 AM #5

I haven't managed to operate the board beyond a successful flashback. It doesn't start or display the UEFI screen.

P
Pyromanicgamer
Junior Member
46
12-02-2022, 02:29 AM
#6
It seems EVGA uses a cap similar to a CMOS jumper to block the green wire during testing. After performing the test, the PSU fan started up. Are these conditions indicating the PSU is functioning properly?
P
Pyromanicgamer
12-02-2022, 02:29 AM #6

It seems EVGA uses a cap similar to a CMOS jumper to block the green wire during testing. After performing the test, the PSU fan started up. Are these conditions indicating the PSU is functioning properly?

Z
zMadeus
Posting Freak
755
12-02-2022, 10:14 AM
#7
Verify all connections once more. Begin with the 6 pin CPU connector. Also ensure the CPU is properly positioned.
Z
zMadeus
12-02-2022, 10:14 AM #7

Verify all connections once more. Begin with the 6 pin CPU connector. Also ensure the CPU is properly positioned.

R
Reepety
Senior Member
374
12-02-2022, 02:23 PM
#8
This situation is quite awkward. I didn't attach the CPU power cable correctly. Despite having experience with building systems, I mistakenly assumed the 20+4 connector of the ATX cable had a "+4" for the CPU. Once I connected it, the system started up quickly and I successfully ran the advertised EXPO profile. I'm really grateful for the assistance!
R
Reepety
12-02-2022, 02:23 PM #8

This situation is quite awkward. I didn't attach the CPU power cable correctly. Despite having experience with building systems, I mistakenly assumed the 20+4 connector of the ATX cable had a "+4" for the CPU. Once I connected it, the system started up quickly and I successfully ran the advertised EXPO profile. I'm really grateful for the assistance!