F5F Stay Refreshed Software Operating Systems Installation issues arise when Windows 11 cannot locate storage devices.

Installation issues arise when Windows 11 cannot locate storage devices.

Installation issues arise when Windows 11 cannot locate storage devices.

B
Bella0810
Member
Find
129
12-03-2021, 01:26 AM
#1
While trying to set up Windows 11 on my new PC, I received a warning: "We couldn't find any drives. To get a storage driver, click Load driver." I’m running an AMD Ryzen 5 5600x with an ASUS ROG STRIX B550-F GAMING WIFI II board. My storage is a Samsung 960 Pro Evo, and there are no other drives connected. The SATA mode is configured to AHCI in the BIOS. I’ve attempted: downloading and installing the AMD RAID driver from the provided link onto a USB drive and loading it during setup. However, when I do, the system reports "No signed device drivers were found. Make sure that the installation media contains the correct drivers, and then click OK." Even after disabling the driver compatibility option. I’m running low on solutions, any advice would be greatly appreciated.
Reply
Reply
B
Bella0810
12-03-2021, 01:26 AM #1

While trying to set up Windows 11 on my new PC, I received a warning: "We couldn't find any drives. To get a storage driver, click Load driver." I’m running an AMD Ryzen 5 5600x with an ASUS ROG STRIX B550-F GAMING WIFI II board. My storage is a Samsung 960 Pro Evo, and there are no other drives connected. The SATA mode is configured to AHCI in the BIOS. I’ve attempted: downloading and installing the AMD RAID driver from the provided link onto a USB drive and loading it during setup. However, when I do, the system reports "No signed device drivers were found. Make sure that the installation media contains the correct drivers, and then click OK." Even after disabling the driver compatibility option. I’m running low on solutions, any advice would be greatly appreciated.

Reply
Reply
S
Sickkid99
Junior Member
Find
1
12-03-2021, 10:14 AM
#2
Windows isn't installed yet, so executables can't run or zip files will fail. Your storage device isn't SATA—it's PCI-E (m.2). No compatible drivers exist for Windows setup. M.2 drives don't require additional drivers on Windows 11; they come pre-installed. The problem lies in your system's UEFI settings. Verify your BIOS/UEFI version matches Windows 11 requirements. If updating, follow your motherboard's instructions precisely. Usually load Optimize Default and save before restarting to apply changes. Ensure the BIOS is updated via your motherboard manual. Disable CSM (Compatibility Support Module), enable UEFI, set Secure Boot to "Windows," and activate TPM with the latest version. Set DOCP/XMP to "Profile 1" or choose the fastest profile. Enable Fast Boot and set POST delay to 0 seconds once everything is stable. Memory Context Restoration should be turned on. Configure M.2 settings: choose Auto or PCIE mode, use maximum bandwidth (ideally x4), and disable unused hardware like SATA controllers since you lack them. Each motherboard differs, so review the manual carefully. If your ASUS guide doesn't cover UEFI, you'll need to troubleshoot independently. There could be additional settings to adjust when booting from a USB drive—look for options labeled "UEFI" or similar in the menu.
Reply
Reply
S
Sickkid99
12-03-2021, 10:14 AM #2

Windows isn't installed yet, so executables can't run or zip files will fail. Your storage device isn't SATA—it's PCI-E (m.2). No compatible drivers exist for Windows setup. M.2 drives don't require additional drivers on Windows 11; they come pre-installed. The problem lies in your system's UEFI settings. Verify your BIOS/UEFI version matches Windows 11 requirements. If updating, follow your motherboard's instructions precisely. Usually load Optimize Default and save before restarting to apply changes. Ensure the BIOS is updated via your motherboard manual. Disable CSM (Compatibility Support Module), enable UEFI, set Secure Boot to "Windows," and activate TPM with the latest version. Set DOCP/XMP to "Profile 1" or choose the fastest profile. Enable Fast Boot and set POST delay to 0 seconds once everything is stable. Memory Context Restoration should be turned on. Configure M.2 settings: choose Auto or PCIE mode, use maximum bandwidth (ideally x4), and disable unused hardware like SATA controllers since you lack them. Each motherboard differs, so review the manual carefully. If your ASUS guide doesn't cover UEFI, you'll need to troubleshoot independently. There could be additional settings to adjust when booting from a USB drive—look for options labeled "UEFI" or similar in the menu.

Reply
Reply