i5 6600k oc issues
i5 6600k oc issues
Hey, I'm trying to set up my new i5 6600k on a gigabyte Z170x UD3 but I'm running into issues. The blue screen appears when the processor hits 4.3ghz, and after adjusting the voltage to help stabilize it at 4.4ghz, the PC crashes every time even when using BIOS. I'm not sure if I'm doing something wrong. This is my first time dealing with overclocking.
I struggle with the LLC setup, but I’m seeing a 4.5ghz at 1.32v occasionally. When I shut down or force restart the BIOS, my settings revert to the last stable configuration. Any suggestions?
Settings tend to reset after system crashes.
Make sure to save your configurations and apply small adjustments when needed.
4.6ghz should work on all CPUs.
Change core multiplier to 46, uncore to 39-45, but keep them different from the core speed.
Set vcore to 1.35, not exceeding 1.4 unless your cooling is adequate.
Ensure DRAM settings are correct and XMP is enabled.
Adjust load line calibration to high.
Review Windows power options,
Run Process Power Management,
Minimum...
I'm having trouble getting my new i5 6600k to run smoothly on the gigabyte Z170x UD3. The system keeps showing a blue screen when it hits 4.3GHz, and after adjusting the voltage slightly to try to stabilize it at 4.4GHz, the PC crashes every time even when using BIOS. I'm not sure if I'm doing anything wrong. This is my first time dealing with overclocking. Not all chips perform equally—some can reach 4.4GHz with a small voltage boost of +0.03v, but it seems unstable. I've been experimenting with different settings and voltages, like trying a 44 multiplier at 1.3v, but it doesn't work consistently. Small adjustments might help.
Usually indicates you've hit the CPU's maximum overclock limit in frequency or MHz.
In certain scenarios, if the base clock speed configured at 100MHz is used for the CPU and memory modules, it might be the issue.
If this applies, consider adjusting the memory or RAM's selected frequency instead of changing the CPU multiplier.
Lower the chosen frequency of the system's RAM or memory.
For instance, reduce from 2400MHz to 2200MHz and test the new multiplier value.
Check if stability returns.
Shaun o :
This usually indicates you've hit the CPU's maximum overclock limit in frequency or MHz.
In certain situations, if you've set the base clock speed to 100MHz as the default for your CPU and the memory modules installed, it might be the issue that the RAM or memory speed you're using is too high.
If this applies, consider adjusting the memory or RAM's selected frequency.
For instance, lowering it from 2400MHz to 2200MHz and then testing the multiplier value again could help.
Check if the system stabilizes after making these changes.
thanks krzy the issue was that i was only using 1.260-1.280v, but now i'm stable at 4.4ghz 50ºc at 1.335v full load. do you think i can go up to 4.5? try changing the multiplier to 45 and check stability with your current voltage.
Your success in overclocking a 6600K depends largely on securing a solid chip.
As of 12/04/2016
The percentage of users achieving an overclock at a reasonable 1.40v Vcore varies.
I5-6600K
5.2 – less than 1% undelidded
4.9 – 14%
4.8 – 38%
4.7 – 67%
4.6 – 87%
The main factor is the Vcore.
I think you might be able to surpass these numbers.
After achieving stability, apply adaptive voltage and speedstep controls.
This will lower the multiplier and thus reduce the Vcore when the processor is idle.
Hey, sorry for the delayed response (was on a family trip) – so far testing a lot, and I noticed something unusual. When I adjusted my Vcore to around 1.3v, after testing stability, I found that my current Vcore is actually at 1.27. Should I still try to fix this? I'm using a Gigabyte Z170x UD3.
I believe that's correct.
When under pressure, the motherboard might not provide the complete voltage.
Don't worry about it.