How to paint a computer case and mod it? Corsair Vengence C70
How to paint a computer case and mod it? Corsair Vengence C70
So im wanting to paint my computer case, currently it is a military green colour, but im wanting it to be completely white, with some baby blue accents. As well as i will be taking off the side panel where there is a window on the case, and replacing it with a acrylic sheet that is the same size, seeing as the case is made out of metal, would it be a bad idea to attach it by using some magnets? Not very strong ones, just so it holds it in place. Or is that a big "no no"?. But how would i go on with painting it? Id like to use spray paint if possible.
Sorry, that custom panel I linked you to earlier wasn't what I thought it was. I thought it was a full window mod with only about an inch of panel around the window. So, yeah, it can be done though but maybe your way with the magnets might be ok. I've never done one that way but I see a few of them out there that are like that. I personally don't like it because they tend to show TOO MUCH, but if that is what you want, that is what you want and what I think doesn't matter.
I prefer there to be about a 1/2-1" strip of the case panel still remaining and then glue the full acrylic or tempered glass panel in place on the inside using epoxy, but if cutting out the panel is too much or you feel uncomfortable, then do as you planned. Worst...
Modify the case with spray paint, utilizing a vinyl dye for plastic parts and a self-etching primer for metal components. Prepare metal surfaces thoroughly with Scotch-Brite pads and sandpaper before priming. For acrylic side panels, enlarge the existing window with an oversized acrylic sheet and adhesive. Numerous online tutorials are available for guidance.
Here’s a rewritten version of the text:
Modifying computer cases can be tricky, especially with discontinued models. I've been working on a case that’s proving difficult to source parts for, and I plan to switch the left and right panels as one side is just a flat panel. I intend to add some RGB lighting and will likely finish this project within the next month.
To address the window issue, enlarging it with an acrylic sheet seems like the best approach – cut the acrylic about 1 inch smaller than the sides of the panel and glue it in place using epoxy adhesive. Proper preparation is key for paint adhesion; sanding metal parts smooth and cleaning them thoroughly with mineral spirits or isopropyl alcohol before applying primer is crucial. For plastic, a good quality primer and surface prep are essential. I typically use spray paint for most modifications, but for plastic parts, I utilize vinyl dye in a spray can.
There are many helpful tutorials available online (examples: [https://www.youtube.com/watch?v=jQqUAaKGRxI](https://www.youtube.com/watch?v=jQqUAaKGRxI) and [https://www.youtube.com/watch?v=Q_YY83dGbEI](https://www.youtube.com/watch?v=Q_YY83dGbEI)). It's important to proceed carefully, especially with discontinued cases!
Just buy one of these and save yourself the headache.
https://mnpctech.com/mnpctech-clear-case...indow.html
Sorry, that custom panel I linked you to earlier wasn't what I thought it was. I thought it was a full window mod with only about an inch of panel around the window. So, yeah, it can be done though but maybe your way with the magnets might be ok. I've never done one that way but I see a few of them out there that are like that. I personally don't like it because they tend to show TOO MUCH, but if that is what you want, that is what you want and what I think doesn't matter. I prefer there to be about a 1/2-1" strip of the case panel still remaining and then glue the full acrylic or tempered glass panel in place on the inside using epoxy, but if cutting out the panel is too much or you feel uncomfortable, then do as you planned. Worst case scenario, it doesn't work out and you go back to your old panel. This guy's turned out looking pretty good, so it might be fine to do it that way. I actually like the way this particular case looks with 100% full side panel.