F5F Stay Refreshed Hardware Desktop Error encountered with Bios Flash.

Error encountered with Bios Flash.

Error encountered with Bios Flash.

Z
ZivShabo
Junior Member
13
05-12-2019, 11:06 AM
#1
You have a 2600 and a x470 SLI master. You upgraded to a 3600 and updated the BIOS, but after installation the system didn’t boot at all—neither the new BIOS nor any other settings worked. After rebooting, you pressed the power button, but it still wouldn’t start. It seems the issue might be with the BIOS update itself or a hardware problem. You may need to try reinstalling the BIOS from scratch or contacting ASRock support for further assistance.
Z
ZivShabo
05-12-2019, 11:06 AM #1

You have a 2600 and a x470 SLI master. You upgraded to a 3600 and updated the BIOS, but after installation the system didn’t boot at all—neither the new BIOS nor any other settings worked. After rebooting, you pressed the power button, but it still wouldn’t start. It seems the issue might be with the BIOS update itself or a hardware problem. You may need to try reinstalling the BIOS from scratch or contacting ASRock support for further assistance.

A
AlperMogulYT
Member
65
05-14-2019, 04:55 AM
#2
Did you turn off the system during the BIOS update? If your board has BIOS Flashback support, you might try that instead. Otherwise, consider resetting the CMOS.
A
AlperMogulYT
05-14-2019, 04:55 AM #2

Did you turn off the system during the BIOS update? If your board has BIOS Flashback support, you might try that instead. Otherwise, consider resetting the CMOS.

R
ryan_TGB
Member
109
05-14-2019, 12:42 PM
#3
The bios update was completed. I said I would restart and press the power button since my 2600 was in.
R
ryan_TGB
05-14-2019, 12:42 PM #3

The bios update was completed. I said I would restart and press the power button since my 2600 was in.

K
Kirito_07
Member
71
05-14-2019, 05:56 PM
#4
What.
K
Kirito_07
05-14-2019, 05:56 PM #4

What.

S
SmartBoysFart
Member
211
05-14-2019, 07:34 PM
#5
No, I did not touch anything.
S
SmartBoysFart
05-14-2019, 07:34 PM #5

No, I did not touch anything.

D
DumpyPutty
Member
172
05-20-2019, 01:34 AM
#6
You damaged the board since you couldn’t let it restart by itself? That’s surprising... Send a return request for the board and avoid handling the BIOS again.
D
DumpyPutty
05-20-2019, 01:34 AM #6

You damaged the board since you couldn’t let it restart by itself? That’s surprising... Send a return request for the board and avoid handling the BIOS again.

M
Mc_cat_rules
Junior Member
47
05-21-2019, 12:43 AM
#7
Start by disconnecting the power cord from the PSU, then take the coin cell battery off the motherboard. Leave it out for about three minutes, then put the battery back in and reconnect the power cord. Try booting up now. You're not sure what will happen yet. It looks like the flash might have completed before you pressed the power button to replace the CPU, which shouldn't have caused any damage.
M
Mc_cat_rules
05-21-2019, 12:43 AM #7

Start by disconnecting the power cord from the PSU, then take the coin cell battery off the motherboard. Leave it out for about three minutes, then put the battery back in and reconnect the power cord. Try booting up now. You're not sure what will happen yet. It looks like the flash might have completed before you pressed the power button to replace the CPU, which shouldn't have caused any damage.

_
_ThePlay
Member
103
05-21-2019, 02:24 AM
#8
The flashing continues until the system automatically restarts. The changes aren’t fully saved until that happens. That’s why you must take your time while updating the BIOS.
_
_ThePlay
05-21-2019, 02:24 AM #8

The flashing continues until the system automatically restarts. The changes aren’t fully saved until that happens. That’s why you must take your time while updating the BIOS.

L
Leyhaya
Posting Freak
801
05-25-2019, 04:18 PM
#9
Completely untrue. At the point the utility says its finished, its finished. Having it carry on working in the background while saying it is finished would be beyond stupid plus there's the fact it will run a byte for byte verification of the EEPROM to make sure the flash completed before it will say its finished. Nothing outside of the EEPROM flash matters, anything stored in NVRAM can be rewritten by the EEPROM at will (which is exactly what happens when you reset your bios to default values or do a full CMOS reset). So again, we cannot assume OP killed their board yet. It's possible they did but just as possible a simple CMOS reset will kick it back into life. Perhaps OP reset before it had chance to fully clear the NVRAM and its now trying to boot from a corrupted BIOS profile. If a CMOS reset doesn't bring it back then its probably dead (assuming OP didn't mess with anything else).
L
Leyhaya
05-25-2019, 04:18 PM #9

Completely untrue. At the point the utility says its finished, its finished. Having it carry on working in the background while saying it is finished would be beyond stupid plus there's the fact it will run a byte for byte verification of the EEPROM to make sure the flash completed before it will say its finished. Nothing outside of the EEPROM flash matters, anything stored in NVRAM can be rewritten by the EEPROM at will (which is exactly what happens when you reset your bios to default values or do a full CMOS reset). So again, we cannot assume OP killed their board yet. It's possible they did but just as possible a simple CMOS reset will kick it back into life. Perhaps OP reset before it had chance to fully clear the NVRAM and its now trying to boot from a corrupted BIOS profile. If a CMOS reset doesn't bring it back then its probably dead (assuming OP didn't mess with anything else).

S
SarvoksSpaces
Junior Member
6
05-27-2019, 01:09 PM
#10
A week passed and I was 235€ behind with an Asus Prime x570. I was heading to the hardware store about 30 minutes before it closed on Monday. I’m glad with the motherboard, even though the BIOS is really frustrating. Still, I plan to try some recovery options or return my old X470 if possible. Thank you all for your quick replies during this stressful time—I really struggled but I believe I won’t fail again. Learning from pain is still the best teacher.
S
SarvoksSpaces
05-27-2019, 01:09 PM #10

A week passed and I was 235€ behind with an Asus Prime x570. I was heading to the hardware store about 30 minutes before it closed on Monday. I’m glad with the motherboard, even though the BIOS is really frustrating. Still, I plan to try some recovery options or return my old X470 if possible. Thank you all for your quick replies during this stressful time—I really struggled but I believe I won’t fail again. Learning from pain is still the best teacher.