F5F Stay Refreshed Hardware Desktop Error detected with new CPU installation, fan malfunction, and over-voltage warning.

Error detected with new CPU installation, fan malfunction, and over-voltage warning.

Error detected with new CPU installation, fan malfunction, and over-voltage warning.

Pages (2): Previous 1 2
S
Santonite
Member
208
09-15-2022, 10:27 AM
#11
Inspect every standoff on the board prior to installation, confirming no additional ones are present that don’t match the mounting holes
S
Santonite
09-15-2022, 10:27 AM #11

Inspect every standoff on the board prior to installation, confirming no additional ones are present that don’t match the mounting holes

W
WaZtoX
Member
115
09-17-2022, 01:49 PM
#12
I removed the drive and it didn’t make a difference. My boot drive remains a SATA SSD. If I save and exit the BIOS, will it harm the CPU or other parts? Is this a bad move? It seems there’s an issue with the motherboard sensors. There are ways to work around it by instructing the system to ignore CPU voltage in the BIOS monitoring area. Edited February 4, 2023 by Camie1o
W
WaZtoX
09-17-2022, 01:49 PM #12

I removed the drive and it didn’t make a difference. My boot drive remains a SATA SSD. If I save and exit the BIOS, will it harm the CPU or other parts? Is this a bad move? It seems there’s an issue with the motherboard sensors. There are ways to work around it by instructing the system to ignore CPU voltage in the BIOS monitoring area. Edited February 4, 2023 by Camie1o

_
_RedStar
Member
171
10-06-2022, 12:22 AM
#13
Could switching to a different PSU improve performance? I have another PC available for testing.
_
_RedStar
10-06-2022, 12:22 AM #13

Could switching to a different PSU improve performance? I have another PC available for testing.

E
EggsyDiamond
Member
166
10-06-2022, 08:27 AM
#14
Consider trying a different PSU, though I'm not sure that's the problem. It might be that the rear standoff was touching the case at the back of the board—though it shouldn't really matter since it just provides ground to that hole. I've seen the ignore option, but you decide. It seems the motherboard may have failed after a BIOS flash; if you've reset them, there should be no remaining settings left. I'd also reinsert the battery, detach the PSU cable from the PSU, remove the 24-pin connector from the PSU, and then leave it for about 10 minutes before turning on the power switch a few times. After that, reconnect everything except the battery and see what happens.
E
EggsyDiamond
10-06-2022, 08:27 AM #14

Consider trying a different PSU, though I'm not sure that's the problem. It might be that the rear standoff was touching the case at the back of the board—though it shouldn't really matter since it just provides ground to that hole. I've seen the ignore option, but you decide. It seems the motherboard may have failed after a BIOS flash; if you've reset them, there should be no remaining settings left. I'd also reinsert the battery, detach the PSU cable from the PSU, remove the 24-pin connector from the PSU, and then leave it for about 10 minutes before turning on the power switch a few times. After that, reconnect everything except the battery and see what happens.

R
RayAnthonyHV
Junior Member
12
10-06-2022, 08:44 AM
#15
I identified the issue as the standoff I had placed on the back, which had a washer with a burr that scratched the board's coating and touched the traces. It functioned properly after removal, so I applied a conformal coating over the damaged area and swapped the washer for a plastic one. It now works perfectly again—thank you all for your assistance!
R
RayAnthonyHV
10-06-2022, 08:44 AM #15

I identified the issue as the standoff I had placed on the back, which had a washer with a burr that scratched the board's coating and touched the traces. It functioned properly after removal, so I applied a conformal coating over the damaged area and swapped the washer for a plastic one. It now works perfectly again—thank you all for your assistance!

Pages (2): Previous 1 2