Ensure proper installation and support for the cable.

F5F Stay Refreshed Power Users Networks Ensure proper installation and support for the cable.

Pages (3): Previous 1 2 3 Next

_ErikThePanda_
Posting Freak

807

01-19-2024, 06:08 PM

#11

They mentioned needing two more units along with the fiber they referenced previously.

_ErikThePanda_

01-19-2024, 06:08 PM #11

They mentioned needing two more units along with the fiber they referenced previously.

Bladestorm117
Junior Member

01-20-2024, 02:55 AM

#12

then single mode it is

Bladestorm117

01-20-2024, 02:55 AM #12

then single mode it is

ImiSiS
Member

01-20-2024, 04:39 AM

#13

Sweden wasn't on my list: https://www.amazon.se/Medienconverter-Si...B07TB4KPPL A few of these might work.

ImiSiS

01-20-2024, 04:39 AM #13

Sweden wasn't on my list: https://www.amazon.se/Medienconverter-Si...B07TB4KPPL A few of these might work.

AT645371
Junior Member

01-26-2024, 08:41 PM

#14

You only need one of each item from those Amazon links. The SFP modules in the kit aren't powerful enough for 150m at 100/100 Mbps.

AT645371

01-26-2024, 08:41 PM #14

You only need one of each item from those Amazon links. The SFP modules in the kit aren't powerful enough for 150m at 100/100 Mbps.

Lord_Thurlvin
Junior Member

01-27-2024, 04:32 AM

#15

Absolutely, I've tested 100g optics on a 1-meter cable for many years without any problems.

Lord_Thurlvin

01-27-2024, 04:32 AM #15

Absolutely, I've tested 100g optics on a 1-meter cable for many years without any problems.

905xA
Senior Member

667

01-27-2024, 05:09 AM

#16

They aren't flawless. These are 20km rated 1310nm SFP modules and you'll need attenuators for such a short run or you could damage the receivers at either end. The Multi-Mode model with a 550m rating would perform better here. Refer:

905xA

01-27-2024, 05:09 AM #16

Crafty_Box
Member

228

01-27-2024, 05:15 AM

#17

Minimum wiring length for -SR, -LRM, -LR, -ER units is 2 meters as per IEEE 802.3ae

Crafty_Box

01-27-2024, 05:15 AM #17

Minimum wiring length for -SR, -LRM, -LR, -ER units is 2 meters as per IEEE 802.3ae

Mathsterbation
Member

01-27-2024, 08:14 AM

#18

This is puzzling you.

Mathsterbation

01-27-2024, 08:14 AM #18

This is puzzling you.

Even_Mornino
Junior Member

01-27-2024, 02:53 PM

#19

I reviewed the video and noticed they employ single-mode fiber along with an optical attenuator. Wouldn't that be suitable for your setup? Calculating the right attenuator value isn't straightforward—consider consulting a network design guide or using simulation tools.

Even_Mornino

01-27-2024, 02:53 PM #19

Rabuz
Junior Member

01-27-2024, 10:51 PM

#20

It seems you're closing off further discussion. Your perspective is clear—I'll respect that.

Rabuz

01-27-2024, 10:51 PM #20

It seems you're closing off further discussion. Your perspective is clear—I'll respect that.

Pages (3): Previous 1 2 3 Next