F5F Stay Refreshed Hardware Desktop Delidding 5800x3d

Delidding 5800x3d

Delidding 5800x3d

H
huityweb
Member
157
04-09-2022, 12:47 PM
#1
Yes, you can adjust the settings to handle strong thermals.
H
huityweb
04-09-2022, 12:47 PM #1

Yes, you can adjust the settings to handle strong thermals.

N
nikko369
Junior Member
35
04-10-2022, 04:01 AM
#2
Undervolting offers better results. Users have successfully lowered the power supply to 1.1 to 1.0 volts. Ryzen chips are built into the IHS and naturally provide strong heat dissipation.
N
nikko369
04-10-2022, 04:01 AM #2

Undervolting offers better results. Users have successfully lowered the power supply to 1.1 to 1.0 volts. Ryzen chips are built into the IHS and naturally provide strong heat dissipation.

S
Silv3rWing
Junior Member
12
04-10-2022, 04:38 AM
#3
It's feasible, though I've only reached about 2700X. Direct die cooling (unplated) achieved roughly a 5°C temperature reduction on that chip. The risk of delamination isn't worth the effort if something goes wrong. If you aim for higher temps, adding a spot fan to the VRM area can improve airflow near the CPU base. This is especially useful with water coolers or tower coolers that don't provide strong face-down airflow like standard cases do.
S
Silv3rWing
04-10-2022, 04:38 AM #3

It's feasible, though I've only reached about 2700X. Direct die cooling (unplated) achieved roughly a 5°C temperature reduction on that chip. The risk of delamination isn't worth the effort if something goes wrong. If you aim for higher temps, adding a spot fan to the VRM area can improve airflow near the CPU base. This is especially useful with water coolers or tower coolers that don't provide strong face-down airflow like standard cases do.

D
DankTimon
Junior Member
2
04-10-2022, 11:07 AM
#4
Did you apply liquid metal or regular paste after removing the outer layer?
D
DankTimon
04-10-2022, 11:07 AM #4

Did you apply liquid metal or regular paste after removing the outer layer?

C
Cheetahfast256
Member
52
04-15-2022, 11:40 PM
#5
Applied regular paste, specifically Antec Formula 7.
C
Cheetahfast256
04-15-2022, 11:40 PM #5

Applied regular paste, specifically Antec Formula 7.

A
AbyssalCricket
Junior Member
2
04-16-2022, 02:44 AM
#6
That’s an error if you used liquid metal; at least you could achieve a 10-degree drop.
A
AbyssalCricket
04-16-2022, 02:44 AM #6

That’s an error if you used liquid metal; at least you could achieve a 10-degree drop.

W
WF_Catt
Posting Freak
761
04-17-2022, 03:17 PM
#7
It's non-conductive and significantly safer... Just avoid handling it. But that was a mistake? No, I don't think so? Re-Plated, TEC cooled, paste, not LM-30c idle 4GHz 1.19V 2700x 16 threads. What do you think? Spoiler alert!
W
WF_Catt
04-17-2022, 03:17 PM #7

It's non-conductive and significantly safer... Just avoid handling it. But that was a mistake? No, I don't think so? Re-Plated, TEC cooled, paste, not LM-30c idle 4GHz 1.19V 2700x 16 threads. What do you think? Spoiler alert!