F5F Stay Refreshed Hardware Desktop Compare RAM speeds and their timing characteristics. Analyze how data transfer rates relate to latency and clock speeds.

Compare RAM speeds and their timing characteristics. Analyze how data transfer rates relate to latency and clock speeds.

Compare RAM speeds and their timing characteristics. Analyze how data transfer rates relate to latency and clock speeds.

Pages (2): Previous 1 2
P
PersieO
Posting Freak
786
11-02-2016, 11:10 AM
#11
Command Rate 2T seems appropriate for these settings. It looks like you've set it up properly now. For further optimization, consider adjusting related parameters.
P
PersieO
11-02-2016, 11:10 AM #11

Command Rate 2T seems appropriate for these settings. It looks like you've set it up properly now. For further optimization, consider adjusting related parameters.

A
AskedRumble52
Member
216
11-02-2016, 11:40 AM
#12
Focus on the key timings here. Refine one at a time and test. Maintain the 1T command speed. Set the memory voltage to 1.36V instead of 1.35V to handle any voltage drop. You can also turn off power-down mode, which will stop the memory from throttling or saving power.
A
AskedRumble52
11-02-2016, 11:40 AM #12

Focus on the key timings here. Refine one at a time and test. Maintain the 1T command speed. Set the memory voltage to 1.36V instead of 1.35V to handle any voltage drop. You can also turn off power-down mode, which will stop the memory from throttling or saving power.

M
magmasnowman
Member
70
11-02-2016, 12:28 PM
#13
M
magmasnowman
11-02-2016, 12:28 PM #13

M
Mouse123
Member
69
11-04-2016, 09:34 AM
#14
Return to 2T for better stability and retest.
M
Mouse123
11-04-2016, 09:34 AM #14

Return to 2T for better stability and retest.

G
Gabokazu
Posting Freak
814
11-04-2016, 04:28 PM
#15
I'm back on 1T again. Your advice about keeping voltage consistent and using 1.36 helped. Do you think a lower CL is better than faster memory? When you raise the memory speed from 15 to 17 to 17 again to 36 to 69 to 1, which timing settings should you adjust?
G
Gabokazu
11-04-2016, 04:28 PM #15

I'm back on 1T again. Your advice about keeping voltage consistent and using 1.36 helped. Do you think a lower CL is better than faster memory? When you raise the memory speed from 15 to 17 to 17 again to 36 to 69 to 1, which timing settings should you adjust?

M
Mario10Gamer
Member
188
11-05-2016, 05:04 PM
#16
Reduce the latency of the Cas system, maintain identical timing, boost frequency until instability occurs.
M
Mario10Gamer
11-05-2016, 05:04 PM #16

Reduce the latency of the Cas system, maintain identical timing, boost frequency until instability occurs.

M
MONSTERmoose91
Senior Member
526
11-25-2016, 01:56 AM
#17
I'm back with 2T and XMP. The standard 3600MHz setting isn't reliable on 1T when things get busy. I'll experiment with various XMP profiles—there are two of them available.
M
MONSTERmoose91
11-25-2016, 01:56 AM #17

I'm back with 2T and XMP. The standard 3600MHz setting isn't reliable on 1T when things get busy. I'll experiment with various XMP profiles—there are two of them available.

C
Charliemc909
Posting Freak
898
11-25-2016, 07:27 PM
#18
It will require some testing and adjustment. You're heading in the correct direction. Most outcomes depend on your decisions. Minor adjustments work best.
C
Charliemc909
11-25-2016, 07:27 PM #18

It will require some testing and adjustment. You're heading in the correct direction. Most outcomes depend on your decisions. Minor adjustments work best.

Pages (2): Previous 1 2