F5F Stay Refreshed Hardware Desktop Cache performance and system agent voltage impact overall efficiency.

Cache performance and system agent voltage impact overall efficiency.

Cache performance and system agent voltage impact overall efficiency.

Pages (2): 1 2 Next
D
Dan_playz_MC
Senior Member
461
05-22-2016, 12:30 PM
#1
It’s a good question. System Agent Voltage might offer some benefit when boosting CPU cache overclocking, but it’s not guaranteed. If you’re mainly focused on RAM overclocking, the separate System Agent Voltage for RAM is likely more effective. Testing is key—monitor stability before adjusting voltages.
D
Dan_playz_MC
05-22-2016, 12:30 PM #1

It’s a good question. System Agent Voltage might offer some benefit when boosting CPU cache overclocking, but it’s not guaranteed. If you’re mainly focused on RAM overclocking, the separate System Agent Voltage for RAM is likely more effective. Testing is key—monitor stability before adjusting voltages.

I
ItsSkinny
Junior Member
4
06-10-2016, 04:17 PM
#2
Unless cache has its own voltage setting, it uses cpu vcore. No reason to use more than 1.20v for system agent or Vccio. It'll kill the chip faster. If you're using that much vcore at 5.2 ghz, it's probably too hot and eventually fails the burn in tests. The heat and vcore will wear the chip out fast. I mean, you should be able to pull off 5ghz cpu all core and 4.7ghz cache with around 1.350v give or take. 5.2ghz, you're just beating the chip.
I
ItsSkinny
06-10-2016, 04:17 PM #2

Unless cache has its own voltage setting, it uses cpu vcore. No reason to use more than 1.20v for system agent or Vccio. It'll kill the chip faster. If you're using that much vcore at 5.2 ghz, it's probably too hot and eventually fails the burn in tests. The heat and vcore will wear the chip out fast. I mean, you should be able to pull off 5ghz cpu all core and 4.7ghz cache with around 1.350v give or take. 5.2ghz, you're just beating the chip.

G
Gashbash
Junior Member
42
06-10-2016, 06:12 PM
#3
You have two 2xx360mm rads and one 240mm rad in a custom loop. Performance isn't too poor. Average temps sit around 85 during heavy use, with the core averaging 1.395. Fans spin at 8x Nactua 3000RPM for maximum cooling—though it does get quite loud.
G
Gashbash
06-10-2016, 06:12 PM #3

You have two 2xx360mm rads and one 240mm rad in a custom loop. Performance isn't too poor. Average temps sit around 85 during heavy use, with the core averaging 1.395. Fans spin at 8x Nactua 3000RPM for maximum cooling—though it does get quite loud.

F
FishFash
Junior Member
13
06-12-2016, 07:50 AM
#4
It's quite warm out—around 85°C, which is right at the stability limit. More heat means increased vcore leakage, explaining why you're close to 1.5v. Leakers often push overclocking during cooler periods or with extreme techniques. I'd say keeping longevity above 1% FPS is a good goal. But definitely not exceeding 1.2v with Vccio or System Agent, even on a CL16 4000MHz DDR4 board. If the system auto-runs those higher speeds, lowering them could help with temperatures.
F
FishFash
06-12-2016, 07:50 AM #4

It's quite warm out—around 85°C, which is right at the stability limit. More heat means increased vcore leakage, explaining why you're close to 1.5v. Leakers often push overclocking during cooler periods or with extreme techniques. I'd say keeping longevity above 1% FPS is a good goal. But definitely not exceeding 1.2v with Vccio or System Agent, even on a CL16 4000MHz DDR4 board. If the system auto-runs those higher speeds, lowering them could help with temperatures.

F
F01lEo
Member
105
06-13-2016, 04:14 AM
#5
I don’t worry too much about my chip; I upgrade every two generations, and sometimes even sooner. My main worry is whether the crash comes from the two low VCore and system agent or if it’s due to the vCore itself.
F
F01lEo
06-13-2016, 04:14 AM #5

I don’t worry too much about my chip; I upgrade every two generations, and sometimes even sooner. My main worry is whether the crash comes from the two low VCore and system agent or if it’s due to the vCore itself.

C
cal_gamer10
Member
105
06-23-2016, 08:51 PM
#6
It's about the temperature, not the voltage. The Asus auto settings are probably stuck at 1.45v SA/IO. Likely the issue isn't the voltages themselves. You managed to get it running for 9 hours, so I recommend lowering the maximum temperature as much as possible. Also, consider turning off C-STATE and using a solid V-CORE value.
C
cal_gamer10
06-23-2016, 08:51 PM #6

It's about the temperature, not the voltage. The Asus auto settings are probably stuck at 1.45v SA/IO. Likely the issue isn't the voltages themselves. You managed to get it running for 9 hours, so I recommend lowering the maximum temperature as much as possible. Also, consider turning off C-STATE and using a solid V-CORE value.

U
Unfrugal
Member
80
06-23-2016, 09:24 PM
#7
I have cstates off of course. CPU VCCIO reads 1.056 and CPU VCCSA is 1.136. They're not particularly high. I've also performed the same test before for about 19 hours with temperatures close to these values. The average temps were in the 80s. The main variation is uncore at 43.
U
Unfrugal
06-23-2016, 09:24 PM #7

I have cstates off of course. CPU VCCIO reads 1.056 and CPU VCCSA is 1.136. They're not particularly high. I've also performed the same test before for about 19 hours with temperatures close to these values. The average temps were in the 80s. The main variation is uncore at 43.

D
Der_HauiHD
Member
144
06-24-2016, 04:37 AM
#8
You might attempt advanced settings and system agents, though it will increase the temperature. Nothing is lost in trying.
D
Der_HauiHD
06-24-2016, 04:37 AM #8

You might attempt advanced settings and system agents, though it will increase the temperature. Nothing is lost in trying.

G
GoldyGirl
Member
70
06-24-2016, 04:43 AM
#9
I'm not sure, but increasing it might work or it could be okay depending on the situation.
G
GoldyGirl
06-24-2016, 04:43 AM #9

I'm not sure, but increasing it might work or it could be okay depending on the situation.

P
Pieftw247
Member
201
06-24-2016, 05:11 AM
#10
These two voltages are used for memory and BCLK overclocking. They don't affect the cache speed.
P
Pieftw247
06-24-2016, 05:11 AM #10

These two voltages are used for memory and BCLK overclocking. They don't affect the cache speed.

Pages (2): 1 2 Next